Siemens SPCK421 Spezifikationen Seite 171
- Seite / 296
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Engineer programming via the browser
15
Configuring zones, doors and areas
171
Siemens AB
A6V10276959
Security Products
18.11.2011
The following parameters (with the exception of the Interlock parameter) are only
relevant in the following cases:
A Calendar is selected (see Schedule [➙ 170]), or
Unset Duration is enabled (has a value greater than zero), or
Both of the above conditions are met.
Auto Set Warning
Enter the number of minutes to display a
warning before Auto Setting. ( 0 - 30 )
Note that the panel sets either at the
scheduled time or at the time defined by the
Delay Unset parameter. The first warning is
displayed at the configured time before the
scheduled time. There are further warnings
starting at one minute before setting time.
Auto Set Cancel
Enables the user to cancel Auto Setting by
entering a code in the keypad.
Auto Set Delay
Enables a user to delay Auto Setting by
entering a code in the keypad.
Keyswitch
Enables Auto Setting to be delayed using
Keyswitch Expander.
Delay Interval
Enter the number of minutes by which to
delay Auto Set. (1 - 300 )
Delay Counter
Enter the number of times that Auto Setting
can be delayed. (0 – 99: 0 = unlimited)
Delay Unset
Enter the number of minutes by which to
delay an Unset. (0 = no delay)
Interlock Group
Select an Interlock Group to assign to this
area. Interlocking only allows one area
within the group to be Unset at any time.
Typically used in ATM areas.
Unset Duration
If area is Unset for longer than this it will Set
automatically. (Range 0 – 120 mins: 0 = not
active).
Dual PIN
If this option is enabled, two PINs are
required to Set or Unset the area with the
keypad. Both PINs must belong to users
who have the required user right for the
operation (Setting or Unsetting).
If the second PIN is not entered within 30
seconds, or it is wrong, then the area cannot
be Set or Unset.
Late Working Support
An example of using the setting and unsetting parameters is for late working
situations where a calendar has been configured for automatic setting of a
premises at a particular time but staff may need to work late on occasion and the
automatic setting needs to be delayed.
- Siemens AB 1
- Copyright 2
- Table of contents 3
- 1 Meaning of symbols 10
- 2 Security 11
- 2.2.2 Transport 12
- 2.2.3 Setup 12
- 2.2.4 Operation 12
- Security 14
- Meaning of hazard symbols 14
- 3 Directives and standards 15
- 4 Technical Data 19
- Technical Data 20
- SPC4000 20
- 4.2 SPC5000 21
- 4.3 SPC6000 23
- 5 Introduction 26
- 6 Mounting system equipment 27
- Standard enclosure 28
- 6.2 Mounting a G3 enclosure 29
- Back Tamper Requirements 30
- Mounting system equipment 31
- Mounting a G3 enclosure 31
- 6.3 Battery installation 34
- 6.4 Mounting a keypad 35
- 6.5 Mounting an expander 35
- 7 Controller hardware 36
- Controller hardware 37
- 8 Door Controller 39
- 9 Wiring the system 40
- 9.1.1 Loop configuration 41
- 9.1.2 Spur configuration 42
- Spur configuration 43
- Star configuration 44
- Multi-drop configuration 44
- Star wiring 46
- Multi-drop wiring 46
- Mixed wiring 47
- 9.1.4 Shielding 48
- 9.1.5 Cable Map 49
- Wiring of a branch expander 50
- Standard wiring 51
- Wiring the system 52
- Wiring the zone inputs 52
- External bell wiring 54
- Plug-in modules 55
- Powering from battery only 56
- 11 Keypad user interface 57
- Keypad user interface 58
- SPCK420/421 58
- Keypad display 59
- Entering numeric values 61
- Entering text 61
- 11.2 SPCK620/623 62
- 11.2.2 LED description 64
- Emergency Keys 66
- Direct Settings 66
- SPCK620/623 67
- 12 Starting the system 68
- 12.2.1 Fast Programmer 69
- 12.4 Creating system users 70
- Receiver area on the keypad 71
- Starting the system 72
- 14.1 SYSTEM STATUS 75
- 14.2 OPTIONS 76
- 14.3 TIMERS 79
- 14.4 AREAS 81
- 14.5 X-BUS 82
- 14.5.2 RECONFIGURE 83
- 14.5.3.1 LOCATE 84
- 14.5.3.2 MONITOR 84
- 14.5.3.3 EDIT KEYPADS 85
- Comfort Keypad Settings 86
- 14.5.3.4 EDIT EXPANDERS 88
- 14.5.4 ADRESSING MODE 90
- 14.5.5 XBUS TYPE 90
- 14.6 WIRELESS 91
- 14.6.1 ADD SENSORS 92
- 14.6.3 ADD WPA 93
- 14.6.4 EDIT WPA 93
- 14.7 ZONES 94
- 14.8 DOORS 94
- Door inputs 95
- Door Groups 95
- 14.9 OUTPUTS 98
- 14.10 COMMUNICATION 101
- 14.10.2 ETHERNET PORTS 102
- 14.10.3 MODEMS 102
- 14.10.4 CENTRAL STATION 103
- 14.10.4.1 ADD 103
- 14.11 TEST 104
- 14.11.3 ZONE MONITOR 105
- 14.11.2 WALK TEST 105
- 14.11.4 OUTPUT TEST 106
- 14.11.5 SOAK TEST 106
- 14.11.6 AUDIBLE OPTIONS 107
- 14.11.7 WPA TEST 107
- 14.11.8 SEISMIC TEST 107
- 14.12 UTILITIES 108
- 14.13 ISOLATE 108
- 14.14 EVENT LOG 109
- 14.15 CHANGE PIN 109
- 14.16 USERS 109
- 14.16.2 EDIT 110
- 14.16.2.1 ACCESS CONTROL 110
- CARD FORMAT 111
- Card attributes 112
- Supported card formats 112
- 14.17 ENGINEER SMS 113
- 14.18 X-10 114
- 14.19 SET DATE/TIME 114
- 14.20 INSTALLER TEXT 115
- 14.21 DOOR CONTROL 115
- 15.1 Ethernet interface 116
- Connect the cable 117
- 15.2 USB interface 118
- Logging into the browser 119
- 15.4 Panel status 120
- 15.4.2 Zones 121
- Performable actions 122
- 15.4.3 Doors 123
- 15.4.4 System alerts 124
- 15.4.5 Areas 125
- 15.4.6 Wireless 125
- 15.4.7 X-Bus 127
- 15.4.8 Logs 128
- 15.4.8.1 System Log 128
- 15.4.8.2 Access Log 128
- 15.5 Users 129
- 15.5.2 User rights 131
- 15.5.3 Access control 134
- 15.5.6 Engineer SMS 138
- 15.6 File Operations 140
- 15.6.1 Upgrading Firmware 141
- Controller Firmware Upgrade 142
- Peripheral Firmware Upgrade 143
- File Operations 144
- SPC controller interface 145
- PC USB interface 145
- For Windows XP and 2000 146
- For Windows Vista 146
- KeypadReleased 148
- 15.6.3.3.1 148
- BrowserReleased 149
- 15.6.3.3.2 149
- 15.7.1 Identification 150
- 15.7.2 Standards 151
- Changing system settings 152
- 15.7.2.1 Installation type 153
- 15.7.2.2 Region 153
- 15.7.2.3 Grade 153
- 15.7.3 Options 154
- System Options 156
- 15.7.4 Timers 160
- 15.7.5 Clock 164
- 15.7.6 Language 164
- 15.8.1 Editing a zone 165
- Domestic 167
- Commercial 167
- Financial 167
- 15.8.2.1 Entry/Exit 168
- 15.8.2.2 Partset Options 168
- 15.8.2.3 Linked Areas 169
- 15.8.2.4 Schedule 170
- 15.8.2.5 Setting/Unsetting 170
- Late Working Support 171
- Temporary Unset 172
- 15.8.2.6 All Okay 173
- 15.8.2.7 Reporting 173
- 15.8.2.8 RF Output 175
- 15.8.2.9 Area Triggers 176
- 15.8.3 Editing a door 177
- Door attributes 178
- Door timers 179
- 15.8.3.1 Door Interlock 180
- 15.8.4 Adding an area group 181
- 15.9.1 Editing an input 182
- 15.9.2 Editing an output 184
- 15.10 X-BUS 190
- 15.10.2 Expanders 195
- Linked Mode 197
- Flexible Mode 197
- 15.10.3 Door Controllers 200
- 15.10.4 Cable Map 202
- 15.10.5 Settings 202
- 15.11 Wireless 203
- Wireless 205
- 15.11.3 Configuring a WPA 206
- 15.11.3.1 Adding a WPA 207
- 15.11.3.2 Editing a WPA 209
- 15.12.1 Serial ports 209
- Configuring communications 210
- 15.12.1.3 Troubleshooting 214
- 15.12.2 Modems 214
- 15.12.2.1 PSTN modem 215
- 15.12.2.2 GSM modem 217
- 15.12.2.3 SMS test 218
- 15.12.2.4 SMS feature 219
- 15.12.2.6 SMS Commands 219
- 15.12.3 Ethernet 221
- 15.12.6 SPC Pro / SPC Safe 224
- SPC Safe 225
- 15.12.7.1 SIA codes 226
- 15.12.8 EDP Setup 229
- 15.12.9 Remote Maintenance 236
- 15.13.1 Calendars 236
- Week Types 237
- Exceptions 238
- 15.13.2 Triggers 239
- 15.13.3 Mapping Gates 241
- To edit a X-10 device 243
- 16.1 PSTN connection 245
- PSTN connection 246
- 16.2 GSM connection 247
- GSM connection 248
- Intruder alarm functionality 250
- Financial mode operation 250
- 17.4 Full and local alarms 251
- Use of common areas: 253
- 19 Audio/Video Verification 254
- 19.4 Viewing Video Images 257
- Audio/Video Verification 258
- Viewing Video Images 258
- 19.5 Configuring Video 259
- 20 Seismic Sensors 262
- Seismic Sensors 263
- Configuring Video 263
- 20.1 Seismic Sensor Testing 264
- Periodic Automatic Testing 265
- Automatic Test on Setting 265
- AREA NAME’ 266
- ZONE NAME’ 267
- 21 Appendix 268
- Appendix 269
- Zone Names 272
- Zone Types 272
- 21.7 SIA Codes 273
- 21.8 CID Codes 278
- 21.10 User PIN combinations 280
- No of digits 281
- 21.12.3 Engineer Access 282
- 21.12.4 Keypad User Logoff 282
- 21.15 Maintenance Smart PSU 283
- 21.16 Zone types 284
- 21.17 Zone attributes 286
- Hardware Requirements 293
- SPC43xx/SPC53xx/ SPC63xx is: 295
Verwandte Produkte und Handbücher für Ziffernblock Siemens SPCK421
Ziffernblock Siemens SPCK422 Bedienungsanleitung
(20 Seiten)
(20 Seiten)
Ziffernblock Siemens SPCK620 Bedienungsanleitung
(63 Seiten)
(63 Seiten)
Ziffernblock Siemens SPCK422 Bedienungsanleitung
(52 Seiten)
(52 Seiten)
Ziffernblock Siemens SPCK 421 Betriebsanweisung
(35 Seiten)
(35 Seiten)
Ziffernblock Siemens SPCK623 Bedienungsanleitung
(20 Seiten)
(20 Seiten)
Ziffernblock Siemens SPCK421 Bedienungsanleitung
(11 Seiten)
(11 Seiten)
Ziffernblock Siemens SPCK620 Betriebsanweisung
(43 Seiten)
(43 Seiten)
Ziffernblock Siemens SPCK620 Bedienungsanleitung
(43 Seiten)
Ziffernblock Siemens SPCK623 Bedienungsanleitung
(14 Seiten)
(14 Seiten)
Ziffernblock Siemens SPCK620 Bedienungsanleitung
(49 Seiten)
(49 Seiten)
Ziffernblock Siemens SPCK421 Bedienungsanleitung
(35 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.111 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern