Siemens HS Spezifikationen PDF herunterladen (Seite 4)

Siemens Building Technologies, Inc. P84391-003B

Sheet 4 of 4

Figure A

FLUSH (4" BOX)

#8-32 SCREWS

4" SQ. X 2-1/8"

DEEP BACKBOX

SCREW COVERS

8 488

AWG #18 AWG #16 AWG #14 AWG #12

MAXIMUM NUMBER OF CONDUCTORS

Figure B

8 888

AWG #18 AWG #16 AWG #14 AWG #12

MAXIMUM NUMBER OF CONDUCTORS

#6-32 SCREWS

SCREW COVERS

FLUSH (2-GANG BOX)

2-GANG x 3-1/2"

DEEP BACKBOX

Figure C

8 888

AWG #18 AWG #16 AWG #14 AWG #12

MAXIMUM NUMBER OF CONDUCTORS

WOOD SCREWS

#8-18 SCREWS

SCREW COVERS

SURFACE MOUNTING

BACKBOX

(MT-SUR-BOX)

Figure D

8 888

AWG #18 AWG #16 AWG #14 AWG #12

MAXIMUM NUMBER OF CONDUCTORS

#8-18 SCREWS

SCREW COVERS

CONCEALED CONDUIT MOUNTING

BACKBOX

(MT-SUR-BOX)

EXISTING

BOX IN WALL

MOUNTING PROCEDURES:

1. This HS-MC model can be flush mounted to a 100mm

backbox (Figure A) or double-gang backbox (Figure B).

It can also be surface mounted to a indoor/outdoor

backbox (Figures C & D). Mounting hardware for each

mounting option is supplied.

2. Conduit entrances to the backbox should be selected to

provide sufficient wiring clearance for the installed

product. Do not pass additional wires (used for other

than the signaling appliance) through the backbox. Such

additional wires could result in insufficient wiring space

for the signaling appliance.

3. When terminating field wires, do not use more lead

length than required. Excess lead length could result in

insufficient wiring space for the appliance.

4. Use care and proper techniques to position the field wires

in the backbox so that they use minimum space and

produce minimum stress on the product. This is

especially important for stiff, heavy gauge wires and

wires with thick insulation or sheathing.

5. Connect field wires to the HS-MC terminal block (polarity

must be observed). Bend the field wires up 90° at the

connection to the terminal block.

6. Carefully push the field wires into the backbox by hand.

Press the HS-MC to the backbox, verifying that it is

seated and aligned correctly.

7. Fasten the HS-MC to the backbox using the supplied

screws.

The HS-MC 110cd setting is Listed for use in sleeping or non-sleeping areas when installed in accordance with appropriate NFPA Standards and the

AHJ.

WARNING: A SMALL POSSIBILITY EXISTS THAT THE USE OF MULTIPLE STROBES WITHIN A PERSON'S FIELD OF VIEW, UNDER

CERTAIN CIRCUMSTANCES, MIGHT INDUCE A PHOTO-SENSITIVE RESPONSE IN PERSONS WITH EPILEPSY. STROBE REFLECTIONS IN A

GLASS OR MIRRORED SURFACE MIGHT ALSO INDUCE SUCH A RESPONSE. TO MINIMIZE THIS POSSIBLE HAZARD, SIEMENS STRONGLY

RECOMMENDS THAT THE STROBES INSTALLED SHOULD NOT PRESENT A COMPOSITE FLASH RATE IN THE FIELD OF VIEW WHICH

EXCEEDS FIVE Hz AT THE OPERATING VOLTAGE OF THE STROBES. SIEMENS ALSO STRONGLY RECOMMENDS THAT THE INTENSITY AND

COMPOSITE FLASH RATE OF INSTALLED STROBES COMPLY WITH LEVELS ESTABLISHED BY APPLICABLE LAWS, STANDARDS,

REGULATIONS, CODES AND GUIDELINES.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital appliance, pursuant to Part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful interference in residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures: 1) Reorient or relocate the receiving antenna, 2) Increase the separation between the

equipment and receiver, 3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected, and 4) Consult the

dealer or an experienced radio/TV technician for help.

1 2 3 4

Kommentare zu diesen Handbüchern

Keine Kommentare

Siemens HS Spezifikationen Seite 4

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Feuerschutz Siemens HS