Siemens SANTIS-ab Bedienungsanleitung Seite 1

User Manual for SANTIS-ab Subscriber Access and Network Termination for ISDN Services

10 The settings are executed as follows. See also flow chart on next page. 1. Hook off and wait for dial tone 2. Dial ∗∗ → The dial tone is switch

11 Start: Hook off Dial ∗∗ Input command number Input parameter value Dial # Setting over? End: Hook on no

12 5. Table of Configuration Commands Parameter-Reset Command-No / Meaning Parameter value Default 010 reset of all parameters to the default valu

13 Multiple Subscriber Number (MSN) Command-No / Meaning Parameter value Default 111 1st MSN for a/b1 0 to 16 digits --- *) 121 2nd MSN fo

14 Hot Line Command-No / Meaning Parameter value Default 181 hot line number for a/b1-interface 0-16 digits --- 182 hot line number for a/b2-in

15 Emergency Mode Priority Switch Command-No / Meaning Parameter value Default 210 emergency mode priority 0 = S-interface 1 = a/b-interface *) 0

16 Type of Terminal Selection (HLC) Command-No / Meaning Parameter value Default 221 type of terminal equipment at a/b1-interface (HLC) 0 = audio

17 Clear Back Time Delay Switch Command-No / Meaning Parameter value Default 311 clear back time delay at a/b1-interface 0 = immediate 1 = 3 minu

18 PABX-Switch Command-No / Meaning Parameter value Default 320 address selection 0 = standard 1 = PABX 0 If both the a/b-interfaces are connect

19 Metering Pulse Switch Command-No / Meaning Parameter value Default 331 Metering pulses at a/b1-interface 0 = off 1 = on 1 332 Metering pulses

2 U mains 230VAC / 50Hz LED for local feeding SIEMENS LED for remote feeding a/b1 a/b2 S S

20 Call Waiting Tone Switch Command-No / Meaning Parameter value Default 341 call waiting tone at a/b1-interface 0 = off 1 = on 1 342 call wait

21 Metering Calculation Command-No / Meaning Parameter value Default 380 amount for one metering pulse 1 to 8 digits country specific 390 curre

22 Calling Line Identification Restriction (CLIR) Switch Command-No / Meaning Parameter value Default 411 CLIR at a/b1-interface 0 = ident. rest

23 Configuration Example 1: Priorising a/b-interfaces during emergency mode 1. Hook off and wait for dial tone, then dial 2. ∗∗ → the dial tone i

24 Configuration Example 2: A fax machine gr.3 is connected to the a/b1-interface. Thus the MSN and HLC are to be set: MSN = 456, HLC = fax gr.2/3

25 Remarks: • There is a time limitation for the programming. If one sequence is not finished within 30 seconds, an internal generated busy tone w

26 6. Troubleshooting 1. Check the green LEDs on the top of the case: both must light steadily. • If the LED designated with ‘local feeding’ is off

27 7. Pin Allocations of the Sockets Interface Pins a/b1, a/b2 4 & 5 S receive 3 & 6 S transmit 4 & 5

Release 1.1 / 07.96 A1608-X6-A-2-7619 USER11.DOC Siemens Switzerland Ltd.

3 Contents 1. Safety Instructions...4 2. Operating Modes ...

4 1. Safety Instructions • Place the SANTIS-ab near a 230 V outlet. • Do not open the case. • Clean the case only with dry or moist cloth.

5 2. Operating Modes The connection to the public telephone network as well as the selection of one of the following three operating modes must be do

6 3. Installation • If both the green LEDs light steadily, the SANTIS-ab is ready for operation (see figure on page 2). The following installation

7 • Connection of the terminal equipments: The sockets for the analog equipments (e.g. telephones, gr.2/3 fax machines, modems) are designated wit

8 4. Configuration • There are only parameters for the a/b-interfaces. Thus there is only a need for a configuration, if the a/b-interfaces are avai

9 If the configuration access (CA) is restricted (can be set and changed by authorized persons, e.g. telecom staff), the configuration for the a