Siemens Advance Network Gateway Bedienungsanleitung Seite 92
- Seite / 95
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
88 •• Data Hiway Testing 2000591-001
How to Test the Data Hiway, Continued
Data Hiway shield lead continuity can be checked by performing the fol-
lowing procedures:
Ground Data Hiway cable shields at only one end of each segment. This
practice reduces ground loop noise.
Step Procedure
1. With Data Hiway communicating with connected Nodes,
temporarily disconnect Channel A shield lead from ground.
2. Connect 10K ohm resistor to disconnected shield and con-
nect battery positive (+) lead to resistor. Resistor should be
in series with the battery. Connect battery negative (-) lead
to unit ground.
3. Connect DVM positive (+) lead to channel A and connect
shield and negative (-) to unit ground. Measured voltage
potential should be 9 Vdc.
4. If 9 Vdc is not measured, the channel A shield line is
grounded at another point; correct problem.
5. Reconnect channel A and shield lead.
6. Repeat steps 1 through 5 for Channel B.
7. Repeat steps 1 through 6 for each shield ground point on
the Data Hiway cable.
Measuring Shield
Continuity
- Advance Network 1
- Gateway with DataNET (ANG_DN) 1
- Copyright Notice 2
- Table of Contents 3
- Table of Contents, Continued 4
- Audience & Purpose 5
- Chapter Contents 5
- Technical Support 6
- Chapter 1 9
- Overview, Continued 10
- ANG_DN Specifications 12
- Continued 13
- Communication 14
- Comparisons 14
- ANG Cable Types 15
- Chapter 2 20
- Unpacking and Inspection 21
- Pre Installation Planning 22
- Instructions 23
- Configurations 23
- Wall Mounting 23
- Rack Mounting 24
- CE Installations 24
- Wiring Requirements 24
- Site Wiring Requirements 25
- DataNET Channels 26
- Copper Wire Site 27
- Requirements 27
- DataNET Channel 28
- Connections 28
- CE Installations, Continued 30
- Wiring Connections 31
- AC Power (Mains) Connections 32
- Data Hiway Connections 35
- More Information 36
- Installation Note 36
- DataNET Connections 38
- DataNET Copper Connections 39
- Description 41
- Required Parts 41
- Fiber Optic Coupler 41
- Chapter 3 45
- Configuring Your PC 46
- Establishing a Connection 50
- Password Format 51
- How to Log Out 51
- How to Log On 51
- Remote Connection 52
- Before You Begin 53
- Command Line 53
- Definitions 53
- Assigning an IP Address 56
- Displaying the ATT 58
- Editing the ATT 60
- Firmware Updates 62
- Firmware Updates, Continued 63
- Chapter 4 65
- Command Summary, Continued 66
- Chapter 5 78
- ANCB Description 79
- ANCB Description, Continued 80
- Communications 81
- Board LEDs 81
- ANCB Ethernet 83
- Controller LEDs 83
- DataNET Troubleshooting Guide 84
- Configuration 85
- Parameter Errors 85
- More Checks 85
- Signal Quality 86
- Problems 86
- Ethernet Network 87
- Information 87
- ADH Channel 88
- Error Log 88
- Chapter 6 89
- Parts Catalog 89
- Available Parts 90
- Appendix 91
- Measuring Shield 92
- Continuity 92
- Glossary 93
- Definitions, Continued 94
- Siemens Applied Automation 95
Verwandte Produkte und Handbücher für Gateways / Controller Siemens Advance Network Gateway
(32 Seiten)Extron electronics ECP 1000 manuales
Manuales del propietario y guías del usuario para No Extron electronics ECP 1000.
Ofrecemos 2 manuales en pdf Extron electronics ECP 1000 para descargar gratis por tipos de documentos: Manual de usuario
Kommentare zu diesen Handbüchern