Siemens SED2 Betriebsanleitung Seite 90
- Seite / 126
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
90/126
Siemens Building Technologies SED2 variable speed drives CM1U5192en
HVAC Products Programming 01.2002
Dependency:
Accessible only if P0701 - P0706=99 (function of digital inputs=BICO)
r1024 CO: Act. fixed frequency Level 3
Displays sum total of selected fixed frequencies.
Unit: Hz Min: - Def: - Max: -
P1025 Fixed frequency mode - Bit 4
Direct selection or direct selection + ON for bit 4.
Unit: - Min: 1 Def: 1 Max: 2
Level 3
Settings:
1=Direct selection 2=Direct selection + ON command 3=Binary coded selection + ON command
Details:
See parameter P1001 for description of how to use fixed frequencies.
P1026[2] BI: Fixed frequency selection Bit 4
Defines origin of fixed frequency selection.
Unit: - Min: 0:0 Def: 722:4 Max: 4000:0
Level 3
Index:
P1026[0] : 1st command data set (CDS) P1026[1] : 2nd command data set (CDS)
Dependency:
Accessible only if P0701 - P0706=99 (function of digital inputs=BICO).
Details:
See P1020 (fixed frequency selection Bit 0) for most common settings.
P1027 Fixed frequency mode - Bit 5
Direct selection or direct selection + ON for bit 5.
Unit: - Min: 1 Def: 1 Max: 2
Level 3
Settings:
1=Direct selection 2=Direct selection + ON command 3=Binary coded selection + ON command
Details:
See parameter P1001 for description of how to use fixed frequencies.
P1028[2] BI: Fixed frequency selection Bit 5
Defines origin of fixed frequency selection.
Unit: - Min: 0:0 Def: 722:5 Max: 4000:0
Level 3
Index:
P1028[0] : 1st command data set (CDS) P1028[1] : 2nd command data set (CDS)
Dependency:
Accessible only if P0701 - P0706=99 (function of digital inputs=BICO).
Details:
See P1020 (fixed frequency selection Bit 0) for most common settings.
P1031 Setpoint memory of the MOP
Saves last motor potentiometer setpoint (MOP) that was active before OFF command or power
down.
Unit: - Min: 0 Def: 1 Max: 1
Level 3
Settings:
0=PID-MOP setpoint will not be stored 1=PID-MOP setpoint will be stored (P2240 is updated)
Note:
On next ON command, motor potentiometer setpoint will be the saved value in parameter P1040 (setpoint of the MOP).
P1032 Inhibit reverse direction of MOP
Inhibits reverse setpoint selection.
Unit: - Min: 0 Def: 1 Max: 1
Level 3
Settings:
0=Reserve direction is allowed 1=Reserve direction inhibited
Dependency:
Motor potentiometer (P1040) must be chosen as main setpoint or additional setpoint (using P1000).
Note:
It is possible to change motor direction using the motor potentiometer setpoint (increase / decrease frequency either by
using digital inputs or BOP/AOP keypad up / down).
P1040 Setpoint of the MOP
Determines setpoint for motor potentiometer control (P1000 = 1).
Unit: Hz Min: -650.00 Def: 10.00 Max: 650.00
Level 2
Note:
If motor potentiometer setpoint is selected either as main setpoint or additional setpoint, the reverse direction will be
inhibited by default of P1032 (inhibit reverse direction of MOP). To re-enable reverse direction, set P1032=0
r1050 CO: Act. Output frequency of the MOP
Display output frequency of motor potentiometer setpoint ([Hz]).
Unit: Hz Min: - Def: - Max: -
Level 3
r1078 CO: Total frequency setpoint
Displays sum of main and additional setpoints in [Hz].
Unit: Hz Min: - Def: - Max: -
Level 3
P1080 Min. Frequency
Sets minimum motor frequency [Hz] at which motor will run irrespective of frequency setpoint.
Unit: Hz Min: 0.00 Def: 10.00 Max: 650.00
Level 1
Note:
Value set here is valid both for clockwise and for counter-clockwise rotation.
Under certain conditions (e.g. ramping, current limiting), motor can run below minimum frequency.
P1082 Max. Frequency
Sets maximum motor frequency [Hz] at which motor will run irrespective of the frequency
setpoint.
Unit: Hz Min: 0.00 Def: 50.00 Max: 150.00
Level 1
Dependency:
Limited internally to 200 Hz or 5 * rated motor frequency (P0305) when P1300 >= 20 (control mode=vector control). The
value is displayed in r0209 (maximum frequency).
Note:
The value set here is valid for both clockwise and counter-clockwise rotation.
The maximum output frequency of variable speed drive can be exceeded if one of the following is active:
Slip compensation=f
max
+ f
slip comp max
,or
Flying restart=f
max
+ f
slip nom
Maximum motor speed is subject to mechanical limitations.
- SED2 variable speed drives 1
- Operating instructions 1
- HVAC Products 01.2002 2
- Table of contents 3
- 1 Introduction 7
- 1.6 Document conventions 8
- 2 Safety instructions 11
- 2.3 Operation 12
- 2.4 Repairs 12
- 3 Mechanical installation 13
- 3.3 Mounting 14
- 5192M01en 17
- 4 Electrical installation 19
- Torx driver T20 21
- Torx screwdriver 22
- SPS: Programmable controllers 23
- Cable routing for frame 24
- Shield connected 25
- Motor cable 25
- Incoming mains voltage 25
- Removing the 27
- I/O module 27
- Removing the cover of the 27
- Removing the operator 28
- Opening the housing: 28
- Frame sizes D and E 28
- FramesizeF 29
- (Ground) 30
- DC+DC+DC+DC- B 31
- R+ B+ B+ 31
- L3 U V WL2L1 31
- Access to the mains 32
- PE L1 L2 L3 34
- Mains voltage inputs 34
- EMC filter 34
- 1 (17) 10 (7) 1 (17) 10 (7) 35
- 4.3.9 Direction of rotation 36
- 5192Z11en 37
- 4.4 Control terminals 38
- 4.5 SED2 block diagram 39
- 5 Commissioning 41
- 5.1.1 DIP switch settings 42
- 5.2 Checklist prior to start 43
- ≥ motor rating? 43
- Operator 45
- Function Effects 45
- 5.4 Commissioning modes 46
- Resulting display 49
- 5.4.7 10 Hz test 50
- 5.4.8 General operation 51
- 6 Programming 53
- See AOP operating 54
- 6.3.1 Digital inputs 55
- DIN6 DIN5 56
- DIN4 DIN3 56
- DIN2 DIN1 56
- 6.3.2 Analog inputs 57
- Signal in % 58
- Time in ms 58
- 6.3.3 Analog outputs 60
- 6.3.6 OFF functions 63
- 6.3.7 Control types 63
- 6.3.8 Communication 63
- 6.4.1 PID controller 64
- CONTROLLER 64
- 5192Z22en 65
- 5192D01en 66
- 5192Z23en 67
- 6.4.4 Staging pumps or fans 68
- Demand or volume flow 69
- 5192D04en 71
- 6.4.6 Bypassing the VSD 73
- P1264 P1262 P1262P1263 74
- 6.4.7 Hibernation mode 75
- P0508[4] Unit 82
- 7 Troubleshooting 107
- 7.2 Error messages 108
- ≤ VSD power (P0206) 108
- 8 Technical data for the SED2 113
- 8.2 Type-specific data 115
- 9 Appendix 119
- 9.2 Applicable standards 120
- 9.3 List of abbreviations 121
- HVAC Products Index 01.2002 123
Verwandte Produkte und Handbücher für Fernseher & Monitore Siemens SED2
Fernseher & Monitore Siemens SED2 Spezifikationen
(132 Seiten)
(132 Seiten)
(25 Seiten)
Fernseher & Monitore Siemens SED2 Wartungshandbuch
(154 Seiten)
(154 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.584 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern