Siemens SCALANCE X-200 Betriebsanleitung Seite 103
- Seite / 198
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Industrial Ethernet SCALANCE X-100 and SCALANCE X-200 Product Line
Operating instructions, 09/2006, A5E00349864 Release 7
5-1
Configuration / diagnostics using remote
mechanisms
5
5.1 Assignment of an IP address
5.1.1 Introduction
Initial assignment of an IP address
Note
The initial assignment of an IP address for an Industrial Ethernet switch of the
SCALANCE X-200 product line is not possible with Web Based Management because this
configuration tool requires that an IP address is already available.
There are three ways of assigning an IP address to an unconfigured device, using:
• DHCP
• STEP 7 V 5.3 plus SVP 1 or higher
• Primary Setup Tool V3 or higher
Before the IP address can be assigned with the setup tool, the SCALANCE X-200 must
be accessible over Ethernet.
Supported operating systems
The Primary Setup Tool can be installed and run under the following operating systems:
• Windows XP Professional
• Windows 2000 Professional SP2
- SIMATIC NET 1
- SCALANCE 1
- Industrial Ethernet 1
- SCALANCE X-100 and 1
- SCALANCE X-200 Product Line 1
- Table of contents 3
- Table of contents 5
- Introduction 8
- 1.1 Introduction 9
- Further documentation 10
- Finding information 10
- Audience 10
- Standards and approvals 10
- Network topologies 11
- Bus topology 12
- Star topology 12
- Network topologies 13
- 2.1 Network topologies 13
- Ring topology 14
- 2.1 Network topologies 16
- Functional description 17
- Coupling possibility 18
- Product properties 19
- Product properties 21
- 3.3 Unpacking and checking 23
- 3.4 SCALANCE X108 24
- Connector pinout 25
- Autonegotiation 25
- Auto polarity exchange 26
- 3.5 SCALANCE X104-2 27
- Transmission rate 30
- Transmission mode 30
- Transmission medium 30
- Transmission range 30
- Connectors 30
- 3.6 SCALANCE X106-1 31
- 3.7 SCALANCE X208 35
- 3.8 SCALANCE X208PRO 38
- 3.9 SCALANCE X204-2 41
- 3.10 SCALANCE X206-1 45
- 3.11 SCALANCE X204-2LD 49
- 3.11 SCALANCE X204-2LD 53
- 3.12 SCALANCE X206-1LD 54
- 3.12 SCALANCE X206-1LD 58
- 3.13 SCALANCE X202-2IRT 59
- 3.14 SCALANCE X204IRT 63
- 3.15 SCALANCE X202-2P IRT 66
- 3.16 SCALANCE X201-3P IRT 70
- 3.17 SCALANCE X200-4P IRT 74
- Area of application 76
- How it works 76
- Diagnostics 77
- Inserting in the C-PLUG slot 77
- Removing the C-PLUG 77
- 3.19 Button 78
- 3.19 Button 79
- 3.20 Displays 80
- 3.20.2 Power display 81
- 3.20 Displays 82
- 3.20 Displays 83
- LED display during startup 86
- Installation and maintenance 94
- Installation 95
- Uninstalling 96
- 4.1.3 Wall mounting 97
- 4.2 Connecting 98
- 4.2.2 Signaling contact 99
- 4.2.3 Grounding 100
- 4.2 Connecting 101
- 4.3 Maintenance 102
- 5.1.1 Introduction 103
- 5.1.2.3 The DLC protocol 105
- Checking 105
- Procedure 105
- Removing a module 109
- 5.2.1 Principle 110
- Internet Browser 111
- 5.2.3 Starting WBM 112
- 5.2.4 LED simulation 113
- 5.2.5 Working with WBM 113
- Buttons 114
- 5.2.6 WBM menus 115
- System Configuration 116
- System Save & Load HTTP 119
- System Save & Load TFTP 120
- System Version Numbers 121
- System Passwords 123
- Fault Mask 126
- Ring redundancy 127
- X200IRT Standby Manager 132
- C-PLUG Information 134
- Agent Configuration 136
- Agent Event Configuration 137
- Port Mirroring 144
- Switch Ports Status 145
- Switch Port Diagnostics 147
- Switch Forwarding Database 148
- Figure 5-39 POF Management 156
- 5.2.7 SNMP 158
- 5.2.7.2 MIB variables 159
- Port Indexes 160
- Supported devices 163
- PROFINET IO functionality 165
- Including the SCALANCE X-200 166
- PROFINET IO functionality 167
- 7.2 Settings in HW Config 171
- 7.2 Settings in HW Config 172
- Port-specific settings 173
- Slot functions 175
- 7.3 Access options with PNIO 176
- Enable_alarms: 177
- Enhanced_Alarm_Mode: 177
- Data record 5: 177
- PortState: 181
- PortType: 181
- Approvals and markings 182
- &RPSOLHVZLWK&)5 183
- DQG 183
- )'$ 183
- Approvals 184
- Approvals and markings 186
- References 187
- Dimension drawings 188
- 10.1 Dimension drawing 189
- Dimension drawings 190
- 10.1 Dimension drawing 190
- Glossary 192
- Glossary 194
- TP port 196
- Index 198
Verwandte Produkte und Handbücher für Netzwerk-Switches Siemens SCALANCE X-200
Netzwerk-Switches Siemens s3-1621 Betriebsanweisung
(128 Seiten)
(128 Seiten)
Netzwerk-Switches Siemens s3-1641 Betriebsanweisung
(242 Seiten)
(242 Seiten)
Netzwerk-Switches Siemens ISGS Betreibershandbuch
(121 Seiten)
(121 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.748 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern