Siemens 270 series Betriebsanleitung Seite 239
- Seite / 274
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Appendix
A.2 System alarms
TP 270, OP 270, MP 270B (WinCC flexible)
Operating Instructions, Edition 03/2004, 6AV6691-1DD01-0AB0
A-13
Number Effect/cause Remedy
140015 Incorrect baud rate
or:
incorrect bus parameter (e.g.I)
or:
OP address > I or: incorrect interrupt vector
(interrupt does not arrive at the driver)
Correct the incorrect parameters.
140016 Configured interrupt is not supported by the
hardware.
Change the interrupt number.
140017 Configured interrupt in use by another driver. Change the interrupt number.
140018 The consistency check was deactivated by
SIMOTION Scout. Only one appropriate note
appears.
Activate the consistency check with SIMOTION Scout
again and reload the configuration in the project.
140019 SIMOTION Scout loads a new project to the PLC.
Connection to the PLC is interrupted.
Wait until the end of the reconfiguration.
140020 The version in the PLC and that in the configuration
(FWX file) do not match.
Connection to the PLC is interrupted.
The following remedies are available:
Load the current version in the PLC using SIMOTION
Scout.
Regenerate the project using WinCC flexible ES, close
WinCC flexible Runtime and restart with a new
configuration.
150000 No additional data is read or written. Possible
causes:
• The cable is defective.
• The PLC does not respond, is defective, etc.
• The connection is established via the wrong
interface.
• The system is overloaded.
Check that the cable is plugged in, the PLC is operational
and the correct interface is used.
Reboot the system if the system alarm is displayed
continuously.
150001 Connection is
!
e-established because the cause
of the interruption has been eliminated.
-
160000 No additional data is read or written. Possible
causes:
• The cable is defective.
• The PLC does not respond, is defective, etc.
• Connection has been established via the wrong
interface.
• The system is overloaded.
Check that the cable is plugged in, the PLC is operational
and the correct interface is used.
Reboot the system if the system alarm is displayed
continuously.
160001 Connection is
!
e-established because the cause
of the interruption has been eliminated.
-
160010 There is no connection to the server because the
server identification (CLS-ID) cannot be
established.
Values cannot be read or written.
Check the access rights.
160011 There is no connection to the server because the
server identification (CLS-ID) cannot be
established.
Values cannot be read or written.
For example, check if
• The server name is correct
• The computer name is correct
• The server is registered
- SIMATIC HMI 1
- HMI device 1
- TP 270, OP 270, MP 270B 1
- (WinCC flexible) 1
- Preface 3
- Online availability 5
- Conventions 5
- Trademarks 5
- Representatives and agents 6
- Training center 6
- A&D Technical Support 7
- Table of contents 10
- Table of contents 11
- Overview 15
- 1.2 Field of Application 16
- Principle 17
- 1.4 Features 18
- Overview 19
- 1.4 Features 19
- Further information 20
- 1.5 Functional scope 21
- 1.5 Functional scope 23
- 1.6 Communication with PLCs 25
- 1.7 Options 26
- 1.7.1.2 PC card / CF card 28
- Cards supported 28
- Remove memory card 29
- 1.7.2 Software options 30
- 2.1 Safety notes 31
- 2.2 General information 31
- Use in residential areas 32
- Plan deployment 33
- 3.2 Installation notes 34
- Installation location 35
- Degree of protection 35
- Ambient conditions 36
- Installation cut-out 37
- OP 270 6" 38
- Installation and connection 39
- MP 270B Ke 40
- , OP 270 10” 40
- OP 270 6” 40
- Installation in front panels 41
- 4.3.1 Conditions 43
- 4.3.2 Interfaces 44
- Communication options 45
- Ground connection 46
- Potential difference 46
- Connection configuration 47
- 4.3.4.1 Connect printer 48
- USB standard keyboar 50
- USB standard mouse 50
- Operating unit 50
- 4.3.5 Connecting the PLC 51
- PROFIBUS-DP/MPI 52
- Operating 52
- Connecting a UPS 54
- Connecting the power supply 56
- Start up 56
- Function test 57
- Switching off the HMI device 57
- Operating the touchscreen 59
- 5.2 MP 270B Keys and OP 270 60
- 1 Function keys 61
- 2 System keys 61
- OP 270 60" keypads 62
- 5.2.2 Function keys 63
- 5.2.3 System keys 64
- Alphanumeric keys 65
- Cursor keys 65
- Labeling 66
- Changing labeling strips 66
- Create labeling strips 67
- 5.2 MP 270B Keys and OP 270 68
- Printing the labeling strips 69
- Connection 70
- 6.1 HMI device loader 71
- 6.2.1 Open Control Panel 72
- Open Control Panel 73
- Change settings 74
- 6.2.2 Communication 75
- 6.2.3 Date/time 75
- 6.2.4 InputPanel 76
- 6.2.5 Network 76
- 6.2.6 OP 77
- 6.2 Windows CE Control Panel 78
- Calibrate touchscreen 79
- 6.2.7 Printer 81
- 6.2.8 Regional Settings 83
- 6.2.9 Screensaver 84
- 6.2.10 System 85
- 6.2.11 UPS 86
- 6.2.12 Volume & Sounds 87
- 6.3 Network operation 88
- Preparations 89
- 6.3.3 Test network 91
- Example 1: Logs 92
- Set date/time 94
- 7.2 Transfer 95
- 7.2.3 Transfer mode options 97
- Transfer mode directories 99
- Project File 99
- Project backup 99
- 7.2.4 Test project 100
- Procedure 101
- 7.2.5 Uploading project 102
- 7.3 System settings 104
- 7.3.2 Set operating mode 105
- 7.4.1 Functions 106
- Introduction 107
- Requirements 107
- Restore 108
- Prepare and backup project 109
- Update operating system 110
- Prepare and backup project 112
- 7.4 Other transfer functions 112
- 7.4.5 Transferring options 114
- See also 116
- 8.1 Screen objects 117
- 8.2 Alarms 118
- 8.3 Tags 119
- 8.4 Logs 119
- Memory options 120
- Alarm logs 120
- 8.5 Reports 121
- Application 122
- System functions 122
- Scripts 122
- 8.7 Safety 123
- Log-off times 124
- User view 124
- Export and import 124
- Print functions 125
- LED control 125
- Operate project 127
- Language switching 128
- Pictograms 128
- Operation 129
- Direct keys 129
- Button action feedback 130
- Acoustic acknowledgement 130
- Visual feedback 130
- 9.1.2.2 Input of values 131
- Screen keyboard 131
- Numeric screen keyboard 131
- Alphanumeric screen keyboard 134
- Keyboard layers 134
- Operate project 137
- General operation 138
- Navigation 138
- Monitor screen settings 139
- In the startup phase 139
- General 140
- Explorer 140
- Dialogs 140
- 9.1.3.3 Input of values 141
- Selection 141
- Purpose 141
- 9.2.1 Button 142
- 9.2.1.2 Touch control 143
- 9.2.1.3 Keyboard control 143
- 9.2.2 Switch 144
- 9.2.3 I/O field 146
- 9.2.4 Graphic I/O field 148
- 9.2.5 Symbolic I/O field 150
- 9.2.6 Alarm indicator 152
- 9.2.7 Alarm view 153
- Operating elements 154
- 9.2.7.2 Touch control 154
- 9.2.8 Simple alarm view 156
- 9.2.9 Recipe view 158
- 9.2.9.2 Touch control 159
- 9.2.9.3 Keyboard control 159
- Keyboard 160
- 9.2.10 Simple recipe view 161
- 9.2.10.2 Touch control 162
- 9.2.10.3 Keyboard control 162
- 9.2.11 Bar 164
- 9.2.12 Trend view 165
- 9.2.12.2 Touch control 166
- 9.2.13 Slider control 168
- 9.2.13.2 Touch control 169
- 9.2.13.3 Keyboard control 169
- 9.2.14 Gauge 170
- 9.2.15 Date/time field 171
- 9.2.16 Clock 173
- 9.2.17 User view 174
- 9.2.18 Simple user view 176
- Entering custom user data 177
- 9.2.19 Status/Force 178
- 9.2.19.2 Touch control 179
- 9.2.19.3 Keyboard control 179
- 9.2.20 Sm@rtClient view 181
- Monitoring mode 182
- Control mode 182
- 9.2.21 Symbol library 184
- Behavior 185
- 9.2.21.2 Touch control 185
- 9.2.21.3 Mouse control 185
- Operating recipes 187
- Recipe view 188
- Recipe screen 188
- 10.2 Structure of recipes 189
- 10.4 Recipe application 191
- Operating recipes 193
- 10.4 Recipe application 193
- Objective 194
- Sequence 195
- 10.5 Displaying recipes 199
- Simple recipe view 200
- Screen change 201
- Creating new recipe records 201
- Copying a recipe data record 202
- Modify recipe record 202
- 10.7 Example 207
- Settings 209
- Maintenance/Service 211
- Clean screen 212
- Protective foil 212
- Supply source 213
- General information 213
- Technical data 215
- Unit dimensions 216
- 12.2 Technical data 219
- Technical data 221
- 12.2 Technical data 221
- 12.3 EMC requirements 222
- 12.4 Interfaces 223
- USB interface 225
- Appendix 227
- A.1.2 ESD guidelines 228
- A.2 System alarms 229
- System alarm parameters 230
- Appendix 231
- A.2 System alarms 231
- Abbreviations 255
- B.1 Abbreviations 256
- Glossary 257
- Glossary 259
- Transfer 262
- Transfer mode 262
- Index 264
- Index 265
Verwandte Produkte und Handbücher für Software Siemens 270 series
Software Siemens S7-400 Wartungshandbuch
(382 Seiten)
(382 Seiten)
Software Siemens AC65 Betriebsanweisung
(123 Seiten)
(123 Seiten)
Software Siemens Simatic M7-400 Bedienungsanleitung
(266 Seiten)
(266 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.037 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern