Siemens EF 83H Series Bedienungsanleitung Seite 21
- Seite / 187
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Overview
1-5
SIMATIC 505 PROFIBUS-FMS CP User Manual
Below
the LEDs is a recessed RUN/STOP toggle switch. The switch can be
moved from one position to another using a small tool, such as a
screwdriver
. The switch is recessed to prevent accidental switching of the
module from one state to another
.
The RESET button is recessed to prevent accidental reset of the module.
When the RESET button is pushed, the module resets as if power were
turned off and then turned on. Therefore, if the RUN/STOP switch is in the
RUN position and the module is functioning properly
, the module begins to
transmit and receive communications after going through a normal
power
-on start-up sequence.
!
WARNING
The
RESET button is for the unusual circumstance in which there is a module
function error that cannot be fixed with the COM5434 Configurator software.
When the RESET button is pushed, the module enters the state of global reset,
which is the same as a power-up. The hardware is reset, all communication is
terminated on all ports, and the LEDs turn off.
Because all communication that is controlled by the module is terminated,
essential messages to other nodes that control I/O functions can be disrupted.
Disrupting communication during plant operation could result in damage to
equipment and/or injury or death to personnel.
T
o avoid possible damage to equipment and/or injury or death to personnel, do
not reset the module without first understanding all possible results based on
the setup of your network.
The
RS-232 port is a 9-pin male D-shell connector
. Y
ou can set the RS-232
port to 9600 baud, 19200 baud, or 38400 baud using a jumper on the board.
The baud rate of the port must be set before the FMS CP module is installed
in the base. See Section 2.2 for instructions on how to set the baud rate of
the port.
The RS-485 PROFIBUS-FMS port is a 9-pin female D-shell connector
. Y
ou
set the baud rate for the PROFIBUS port during network configuration
using the COM5434 Configurator
, as decribed in Section 5.4.
RUN/STOP Switch
RESET Button
RS-232 Port
PROFIBUS-FMS Port
- PROFIBUS-FMS Communications 1
- Processor (505–CP5434–FMS) 1
- MANUAL PUBLICA 3
- TION HISTOR 3
- OF EFFECTIVE P 4
- Contents 5
- Contents v 7
- Chapter 7 Diagnostics 9
- List of Figures 11
- List of Figures (continued) 12
- Contents xi 13
- Overview 17
- 1.2 Hardware Overview 20
- 1.3 Network Overview 22
- Network Overview (continued) 24
- Installing 27
- the Module 27
- 2.1 Overview of Installation 28
- Installing the Module 30
- torque: 2.6 in-lb (0.3 N-m) 31
- Backplane connectors 31
- 2.6 Powering Up the Base 34
- Connecting 39
- the Network 39
- 3.1 Cables and Connectors 40
- Connecting the Network 41
- 3.2 Cable Routing 43
- Cable Routing (continued) 44
- Communication 52
- Services 52
- 4.1 Overview 53
- Communication Services 54
- Overview (continued) 55
- 4.2 Addressing 58
- 4.3 FMS Services 59
- FMS Services (continued) 61
- 4.4 Send-Receive Services 62
- 4.5 Peerlink II Services 63
- 4.6 S7 Services 64
- the COM5434 Configurator 65
- A:\SETUP 66
- *Standard-Mixed 78
- 5.6 Defining FMS Connections 83
- 5.7 Defining FDL Connections 87
- Local LSAP Enter 89
- Remote LSAP Enter 89
- 5.9 Configuring FMS Jobs 91
- 5.11 Creating FMS Data Types 97
- Definition When 99
- 5.12 Creating FMS Variables 100
- Enter a memory 102
- Use Index? Select 104
- Sub Index You 104
- Configuration 108
- Examples 108
- 6.1 Overview 109
- Configuration Examples 110
- Data Flow 111
- Figure 6-10 FMS 120
- Figure 6-16 Send 130
- Figure 6-17 Receive 132
- Red Box PLCBlue Box PLC 135
- Diagnostics 147
- 7.1 CP Status 148
- 7.2 Active Stations 149
- 7.3 PROFIBUS Statistics 150
- 7.4 FMS Connection Status 151
- 7.5 FDL Connection Status 152
- 7.6 Job Status 153
- 7.7 Peer Block Status 154
- Reference 155
- A.1 Data Element List 156
- Element List (continued) 157
- Data Element List (continued) 158
- Reference Data 161
- 12345678910111213141516 163
- Structure 165
- Identify Response 167
- A.6 Local LSAP Assignments 172
- Troubleshooting 173
- B.1 Using the RESET Button 174
- B.2 Job Status Codes 175
- Job Status Codes (continued) 176
- Specifications 180
- Index-2 183
- Index-4 185
- Customer 186
- Response 186
- FIRST CLASS 187
- PERMIT NO.3 187
- JOHNSON CITY 187
Verwandte Produkte und Handbücher für Kochfelder Siemens EF 83H Series
Kochfelder Siemens ET6 RM Bedienungsanleitung
(138 Seiten)
(138 Seiten)
(44 Seiten)
Kochfelder Siemens ET6..TF.. Bedienungsanleitung
(64 Seiten)
Kochfelder Siemens ET 73501 Bedienungsanleitung
(104 Seiten)
(104 Seiten)
Kochfelder Siemens ET 72518 Bedienungsanleitung
(104 Seiten)
(104 Seiten)
Kochfelder Siemens ET 73571 Bedienungsanleitung
(104 Seiten)
(104 Seiten)
Kochfelder Siemens ET 74534 Bedienungsanleitung
(104 Seiten)
(104 Seiten)
Kochfelder Siemens ET 73506 Bedienungsanleitung
(104 Seiten)
(104 Seiten)
Kochfelder Siemens ET 72539 Bedienungsanleitung
(104 Seiten)
(104 Seiten)
Kochfelder Siemens ET 74500 Bedienungsanleitung
(104 Seiten)
(104 Seiten)
Kochfelder Siemens ET 72522 Bedienungsanleitung
(104 Seiten)
(104 Seiten)
Kochfelder Siemens ET 73583 Bedienungsanleitung
(104 Seiten)
(104 Seiten)
Kochfelder Siemens ET 72586 Bedienungsanleitung
(104 Seiten)
(104 Seiten)
TOA SR-FB4 manuels
Manuels d'utilisation et guides de l'utilisateur pour Acoustique TOA SR-FB4.
Nous fournissons des manuels en pdf 1 TOA SR-FB4 à télécharger gratuitement par type de document : Manuel de l'utilisateur
Kommentare zu diesen Handbüchern