Siemens SIMATIC NET PROFIBUS Wartungshandbuch Seite 231
- Seite / 238
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Glossary
DP Base Programming Interface for CP 5613/CP 5614
C79000-G8976-C108-01
231
FREEZE mode
The FREEZE mode is a DP mode in which the process data are acquired at the
same time from all (or a group) of DP slaves. The time at which the data are
required is indicated in the FREEZE command (a synchronization control frame).
Gap update factor
A free address area between two active nodes is checked cyclically by the node
with the lower PROFIBUS address to find out whether or not another station is
requesting to enter the logical ring. The cycle time for this check is as follows:
gap update factor x target rotation time [ms]
Group identifier
DP slaves can be assigned to one or more groups using a group identifier. The DP
slaves can then be addressed by the group identifier when transferring control
frames.
Highest PROFIBUS address
A bus parameter for PROFIBUS. This specifies the highest PROFIBUS address of
an active node on the PROFIBUS. For passive nodes, PROFIBUS addresses
higher than the HSA are permitted (possible values: HSA 1 to 126).
HSA
H
ighest
S
tation
A
ddress - one of the bus parameters. Specifies the highest node
address used in the network.
Hardware event
Event whose arrival is monitored by the hardware of the CP (at the start of the
cycle, when data changes, when diagnostic data arrive, and when a fast logic
condition arrives).
Input data
Here: the data read cyclically by the DP master from the slaves.
- SIMATIC NET 1
- DP Base Programming Interface 1
- Purpose of the Manual 3
- Validity of the Manual 3
- Guide to the Manual 3
- Contents 5
- Procedure 10
- Overview of PROFIBUS DP 13
- The Advantages of DP 15
- Distributed I/Os 16
- Node Classes 16
- DP Master Class 1 16
- DP Master Class 2 16
- DP Slave 17
- Output Data 18
- Input Data 18
- DP application 20
- Initialization 21
- Parameter Assignment 21
- Configuration 21
- State of the Slave 21
- Diagnostics 22
- 2.6 Modes of the DP Master 23
- Setting the Operating Mode 24
- 2.8 Reliability of DP 27
- Purpose of Control Frames 28
- Creating Groups 28
- Control Commands 29
- 2.10 Typical Sequences in DP 30
- Receiving Diagnostic Data 31
- DP/DPC1 prog 32
- DP-V1 Master Class 2 (DPC2) 33
- 3.1 Functions and Data 38
- Using the DP Database 40
- Configuring Slave Data Areas 40
- Activating the Watchdog 40
- The Read Consistency Option 42
- Reducing Load on the PC CPU 43
- Possible Hardware Events 43
- 3.5 Fast Logic 44
- Properties of Hardware Events 45
- Properties of Software Events 45
- 3.7 Typical Sequences 47
- Shutdown Sequence 48
- Elements of a Polling Cycle 50
- Initializing the Semaphores 53
- Using Hardware Events 54
- Clearing the Semaphores 55
- Using Semaphores for DPC1 56
- Clearing a Semaphore 57
- Software) 58
- Productive Operation 59
- Polling Productive Operation 61
- Initializing the Semaphore 62
- Clearing the Semaphore 63
- Multiple CP Operation 64
- Multiple Application Programs 64
- Multiple CPUs in one PC 64
- Error Codes 65
- Conventions in the Text 66
- Header Files 67
- Auxiliary Functions 69
- Fast Logic 69
- 4.1.2 DP_start_cp 70
- 4.1.3 DP_reset_cp 71
- 4.1.4 DP_open 72
- 4.1.5 DP_get_pointer 73
- 4.1.6 DP_release_pointer 75
- 4.1.7 DP_close 76
- 4.1.8 DP_get_err_txt 78
- 4.1.9 DP_set_mode 79
- 4.1.10 DP_slv_state 81
- 4.1.11 DP_read_slv_par 83
- 4.1.12 DP_global_ctrl 85
- 4.1.13 DP_ds_read 87
- 4.1.14 DP_ds_write 90
- 4.1.15 DP_read_alarm 93
- 4.1.16 DP_alarm_ack 96
- 4.1.17 DP_get_actual_cfg 99
- Parameters 100
- Return Value 101
- 4.1.18 DP_enable_event 102
- C79000-G8976-C108-01 103
- Table continued on next page 105
- 4.1.19 DP_disable_event 107
- 4.1.20 DP_get_result 108
- 4.1.21 DP_get_cref 111
- 4.1.22 DP_init_sema_object 112
- 4.1.23 DP_delete_sema_object 114
- 4.1.24 DP_fast_logic_on 115
- 4.1.25 DP_fast_logic_off 116
- Administrative Functions 118
- Initialization Functions 118
- Standard DP Functions 119
- 4.2.2 DPS_open 120
- 4.2.3 DPS_close 124
- 4.2.4 DPS_start 125
- 4.2.5 DPS_stop 126
- 4.2.6 DPS_get_baud_rate 127
- 4.2.7 DPS_get_gc_command 129
- 4.2.8 DPS_get_state 131
- 4.2.9 DPS_set_diag 133
- 4.2.10 DPS_get_ind 135
- 4.2.11 DPS_set_resp 140
- 4.2.12 DPS_calc_io_data_len 142
- Overview of the Existing Data 143
- Consistent Reading 144
- Example of Consistent Reading 144
- Reading without Consistency 145
- General Notes 147
- Writing is always consistent 148
- Example of Consistent Writing 149
- Uses of the Slave State 152
- Overview 159
- Example of Access 159
- Example of Activation 162
- Example of Deactivation 163
- 4.4 Error Codes 167
- Meaning of the Errors 170
- Description 171
- Error_Decode = DP V1 172
- Error_Code_1 173
- Order of the Slave Data 175
- Format of Data Words 175
- Explanation 176
- Possible Length 177
- Byte 1 (Stationstatus_1) 179
- Byte 2 (Stationstatus_2) 180
- Byte 3 (Stationstatus_3) 180
- Byte 4 (Diag. Master_Add ) 180
- Bytes 5 and 6 (Ident_Number) 181
- Structure 182
- Byte 1 (Header Byte) 182
- Extensions) 183
- Byte 2 (Alarm_Type Variant) 184
- Byte 2 (Status_Type Variant) 184
- Byte 3 (Slot Number Variant) 184
- Byte 5-63 186
- Content of the Data Field 188
- Channel Number 190
- Type of Diagnostics 191
- Definition 193
- Byte Structure 194
- Slave Type 195
- Alarm_Mode 196
- Add_Sl_Flag 196
- Byte 1 (Station_status) 198
- Byte 7 (Group_Ident) 199
- Byte 8 (DPV1_Status_1) 199
- Byte 9 (DPV1_Status_2) 200
- Bytes 11 to n 201
- Overview of the Structure 202
- Structure of an ID Byte 203
- Length Bytes 204
- CP 5613/CP 5614? 207
- Where to Get Help 217
- Documentation 218
- Who to Contact 218
- Common Questions 218
- SIMATIC Training Center 221
- Glossary 227
- User watchdog 237
- Watchdog 237
Verwandte Produkte und Handbücher für Vernetzung Siemens SIMATIC NET PROFIBUS
Vernetzung Siemens SPC3 Spezifikationen
(94 Seiten)
(94 Seiten)
Vernetzung Siemens SX763 Bedienungsanleitung
(20 Seiten)
(20 Seiten)
Vernetzung Siemens S5-135U/155U Bedienungsanleitung
(572 Seiten)
(572 Seiten)
Vernetzung Siemens SE366 Bedienungsanleitung
(124 Seiten)
(124 Seiten)
Vernetzung Siemens AC75 Spezifikationen
(120 Seiten)
(120 Seiten)
Vernetzung Siemens E-110-I Bedienungsanleitung
(23 Seiten)
(23 Seiten)
Vernetzung Siemens 6RA70 Spezifikationen
(130 Seiten)
(130 Seiten)
Vernetzung Siemens SL2-141 Bedienungsanleitung
(24 Seiten)
(24 Seiten)
Vernetzung Siemens TC35 Spezifikationen
(34 Seiten)
(34 Seiten)
Vernetzung Siemens 6RA70 Bedienungsanleitung
(12 Seiten)
(12 Seiten)
Vernetzung Siemens I-SURF Wartungshandbuch
(170 Seiten)
(170 Seiten)
Vernetzung Siemens CL-110-I Bedienungsanleitung
(109 Seiten)
(109 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.118 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern