Siemens COM32 Betriebsanweisung Seite 84
- Seite / 126
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Using the Setup Assistant ION Setup User Guide
Page 84 © 2010 Schneider Electric. All rights reserved.
Demand Screen
Demand is a measure of average power consumption over a fixed time interval.
Peak (or maximum) demand is the highest demand level recorded during a billing
period. From the Demand screen, you can configure Rolling Block (the interval
used to compute your values) and Demand Forgiveness (the time during power
restoration when demand is not calculated).
With Rolling Block (or Sliding Window) Demand, demand is measured based on
the average load level over the most recent set of sub-intervals. The Rolling Block
tab allows you to define the number and length of intervals used for demand
calculations.
Demand Forgiveness is the time, programmed in the meter, during which demand
(and therefore peak demand) will not be calculated following a total power outage.
During power-up following a complete power outage, customer equipment
consumes a higher-than-normal amount of power. The Demand Forgiveness
feature lets a utility forgive the customer for peak demand penalties that may arise
from power-up following a power outage.
Input / Output Screens
The following sections outline the screens available for I/O configuration.
NOTE
The available screens vary depending upon the model and firmware of your connected device. See your
device documentation for specific information on configuring inputs and outputs.
- PowerLogic ION Setup 2.2 1
- Terminology 3
- Contents 5
- Chapter 1 Introduction 7
- ION Setup Features 8
- System Requirements 9
- Overview 10
- Getting More Information 11
- Installing ION Setup 12
- Communicating with Devices 13
- Connecting to serial devices 14
- Using Modem Communications 15
- Using Ethernet Communications 16
- List of Common Procedures 20
- Starting ION Setup 22
- Using the Network Viewer 26
- Left and right panes 27
- ION Setup Commands 28
- Menu Command Effect 29
- Viewing Options 31
- Viewing the unassigned group 32
- Basic versus Advanced Mode 33
- Setting Up Options 34
- Confirmation tab 35
- Security tab 35
- Conventions tab 37
- Applying Security 38
- Working in Single Device Mode 44
- Using Serial Communications 45
- Using Offline Programming 46
- Working in Network Mode 48
- Adding and Configuring Sites 49
- IP Port Description 52
- Adding a New Meter 53
- Grouping Devices 54
- Assigning a Device to a Group 55
- Editing Site Properties 55
- Editing Group Properties 58
- Editing Meter Properties 58
- Description 59
- Setup Screen Examples 62
- Example 3 63
- Example 4 63
- Overview of ION Architecture 66
- Creating new ION modules 67
- Linking ION modules 68
- ION Meter Cloning 72
- In this Chapter 73
- Setup Assistant Overview 74
- Template Screen 75
- Template Paste options 76
- Basic Setup Screen 77
- Security Screen 78
- Communications Screens 81
- 3rd Party Protocols Screen 81
- Clock Screen 83
- Demand Screen 84
- Input / Output Screens 84
- LED Pulsing Screen 85
- Energy Pulsing Screen 85
- OnBoard Digital Inputs Screen 86
- Analog Outputs Screen 86
- Memory Screen 87
- Event Log Screen 89
- EnergyDemand Log Screen 90
- Configuring Interval/Depth 91
- PT/CT Correction Screen 92
- Transformer Loss Screen 92
- Time of Use (TOU) Screen 93
- Sunday--and click OK 96
- Alarming Screen 98
- Power Quality Screen 99
- Displays Screen 99
- The Display Editor appears 100
- Verification Screen 101
- Phasor Viewer 103
- Reports Screen 104
- Writing to Multiple Registers 107
- In this chapter 109
- Displaying Data 110
- Closing data screens 111
- Performing Control Operations 112
- Chart Plotting 113
- Editing chart properties 114
- Chapter 6 Troubleshooting 117
- Troubleshooting ION Setup 118
- ION Setup Diagnostics Tools 119
- Troubleshooting Devices 122
- PowerLogic™ ION™ Setup 126
- User Guide 126
- Schneider Electric 126
Verwandte Produkte und Handbücher für Software Siemens COM32
Software Siemens SIMATIC NET Betriebsanweisung
(68 Seiten)
(68 Seiten)
Software Siemens SIMATIC NET Spezifikationen
(268 Seiten)
(268 Seiten)
Software Siemens v1.0 Wartungshandbuch
(202 Seiten)
(202 Seiten)
Software Siemens 270 series Betriebsanleitung
(274 Seiten)
(274 Seiten)
Software Siemens S7-400 Wartungshandbuch
(382 Seiten)
(382 Seiten)
Software Siemens AC65 Betriebsanweisung
(123 Seiten)
(123 Seiten)
Software Siemens Simatic M7-400 Bedienungsanleitung
(266 Seiten)
(266 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.112 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern