Siemens AC75 Bedienungsanleitung Seite 535
- Seite / 569
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
AC75 AT Command Set
23. Appendix
s
AC75_ATC_V01.002 Page 535 of 569 10/30/06
Confidential / Released
23. Appendix
23.1 Restricted access to SIM data after SIM PIN authentication
Users should be aware that when using a phonebook, SMS or Remote SAT command quickly after SIM PIN
authentication the SIM data may not yet be accessible, resulting in a short delay before the requested AT com-
mand response is returned. This delay is due to the initial process of loading SIM data once after SIM PIN authen-
tication. The duration of loading SIM data is dependent on the SIM card used and may take a couple of seconds.
The "^SSIM READY" URC enabled with AT^SSET can be used to notify the user when the ME has finished read-
ing the SIM card and SIM data are accessible after SIM PIN authentication. Of course, all phonebook and SMS
commands may be issued before the URC is delivered. In this case the AT command response (for example the
complete phonebook) will appear after the delay mentioned above, but before the "^SSIM READY" URC is dis-
played. See example below.
After the "+CREG: 1" (or "+CREG: 5") URC and before the "^SSIM READY" URC it is not sure that outgoing and
incoming calls can be made and short message functions executed. Emergency calls are possible. Outgoing and
incoming calls are always possible AFTER having received the "+CREG: 1" (or "+CREG: 5") and "^SSIM READY"
URCs. See also Section 8.4, Network registration.
Example:
AT^SSET
=1
Activate the "^SSIM READY" URC.
OK
AT&W Store the presentation mode of the "^SSIM READY"
URC to the user profile.
OK
AT+CFUN
=1,1
Restart the ME.
OK
^SYSSTART
The ME was restarted.
AT+CPIN Enter the SIM PIN.
OK
AT+CPBW
=50,"+4030123456789",145,"Paul"
Write a new phonebook record.
OK
^SSIM READY
The URC now confirms that the ME has finished
reading data from the SIM.
AT+CPBR
=50,50
Read the phonebook entered before.
+CPBR: 50,"+4030123456789",145,"Paul"
The phonebook entry was properly saved.
- AT Command Set 1
- Contents 3
- AC75 AT Command Set 10
- List of Tables 12
- List of Figures 13
- 1. Introduction 14
- 1.2 Related documents 15
- 1.3 Document conventions 16
- 1.3.1 Quick reference table 16
- 1.4 AT Command Syntax 18
- 1.4.1 Using Parameters 18
- 1.5 Supported character sets 20
- 1.10 Errors and Messages 31
- 2. Configuration Commands 32
- 2.2.1 AT&V responses 34
- 3. Status Control Commands 80
- 3.2 AT+CIND Indicator control 82
- 3.4.2 SIEMENS L2 cause 94
- Management (SM) 95
- 4.1 AT\Q Flow control 105
- 4.5 ATE Enable command echo 109
- 4.9.1 Autobauding 117
- 5. Security Commands 124
- 5.4 AT+CLCK Facility lock 134
- 5.5 AT^SLCK Facility lock 139
- 5.6 AT+CPWD Change Password 140
- 5.7 AT^SPWD Change Password 144
- 5.8 AT^SCSL Customer SIM Lock 146
- 6. Identification Commands 150
- 7. Call related Commands 156
- 7.2 ATA Answer a call 157
- 7.10 AT+CHUP Hang up call 167
- 7.29 ATP Select pulse dialing 193
- 7.30 ATT Select tone dialing 193
- 8. Network Service Commands 194
- 8.5 AT+CSQ Signal quality 203
- 8.6 AT^SMONC Cell Monitoring 204
- 8.7 AT^SMOND Cell Monitoring 206
- 8.9.1 AT^MONI responses 211
- 8.9.2 Service states 212
- 8.10.1 AT^MONP responses 214
- 8.11 AT^SMONG GPRS Monitor 215
- 8.13 AT^SHOM Display Homezone 219
- 9.5 AT+CCUG Closed User Group 230
- 9.7 AT+CCWA Call Waiting 236
- 10. Internet Service Commands 253
- 10.11.1 Example: Ping 292
- Another Host 299
- 11. GPRS Commands 308
- 12. FAX Commands 352
- 12.4 AT+FRM Receive Data 355
- 12.5 AT+FRS Receive Silence 356
- 12.7 AT+FTM Transmit Data 358
- 13.1 SMS parameters 360
- 14. SIM related Commands 402
- 15.3 Related AT Commands 426
- 16.2 ^SSTN SAT Notification 430
- 16.4 AT^SSTR SAT Response 432
- 17. Phonebook Commands 433
- 17.2 AT+CNUM Read own numbers 434
- 18. Audio Commands 456
- 18.5 AT+CMUT Mute control 459
- 18.6 AT+VTD Tone duration 460
- 19. Hardware Related Commands 481
- 19.2 AT+CALA Set alarm time 482
- 19.3 AT^SAD Antenna Diagnosis 485
- 19.6.1 Deferred shutdown 492
- 19.8.2 Selecting SPI Mode 499
- 19.8.5 Example: Using I²C Bus 504
- 20. GPIO Commands 508
- 21. Java related Commands 521
- 22. Miscellaneous Commands 529
- 23. Appendix 535
Verwandte Produkte und Handbücher für Mobiltelefone Siemens AC75
Mobiltelefone Siemens C62 Bedienungsanleitung
(69 Seiten)
(69 Seiten)
Mobiltelefone Siemens SXG75 Bedienungsanleitung
(166 Seiten)
(166 Seiten)
Mobiltelefone Siemens A35 Bedienungsanleitung
(43 Seiten)
(43 Seiten)
Mobiltelefone Siemens M30 Bedienungsanleitung
(31 Seiten)
(31 Seiten)
Mobiltelefone Siemens CXT65 Bedienungsanleitung
(141 Seiten)
(141 Seiten)
Mobiltelefone Siemens S56 Bedienungsanleitung
(152 Seiten)
(152 Seiten)
Mobiltelefone Siemens AX75 Bedienungsanleitung
(28 Seiten)
(28 Seiten)
Mobiltelefone Siemens C30 Bedienungsanleitung
(31 Seiten)
(31 Seiten)
Mobiltelefone Siemens MC60 Bedienungsanleitung
(118 Seiten)
(118 Seiten)
Mobiltelefone Siemens CX70 Bedienungsanleitung
(74 Seiten)
(74 Seiten)
Mobiltelefone Siemens GSM 900 Bedienungsanleitung
(115 Seiten)
(115 Seiten)
Mobiltelefone Siemens A60 Bedienungsanleitung
(62 Seiten)
(62 Seiten)
Mobiltelefone Siemens S40 Bedienungsanleitung
(50 Seiten)
(50 Seiten)
Mobiltelefone Siemens SL75 Bedienungsanleitung
(139 Seiten)
(139 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.214 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern