Siemens OSM Bedienungsanleitung Seite 42
- Seite / 158
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Important OSM/ESM Functions
2-22
Industrial Ethernet OSM/ESM Network Management
C79000-G8976-C137-08
Table 2-2
Status
Meaning Possible Cause Remedy
disabled (
1
) Observer function is
disabled.
starting (
1
) The Observer is
waiting for test frames
from the RM.
The Observer was
started but no RM
was found.
Check the cable and
device functions as
well as the correct
wiring between the
Observer and RM.
monitoring (
1
) The Observer
monitors the RM
function. This is the
normal state.
rm error : hardware fault(
2
)
rm cfg/hardware error
rm error : test frames missing
rm error : rm status mismatch
(
2
)
Error in the
functioning of the RM
Bad wiring , device
and/or wiring
defective
Check the wiring
between the
Observer and RM
according the
instructions. Check
whether cable and
device function
correctly. Problem
indicators are the
traffic and RM LEDs
and the statistics
counters of the ring
ports.
cfg error : more than one
observer
There is more than
one Observer in the
ring.
More than one
Observer in the ring.
Check the device
configuration. Only
one device may be
configured as the
Observer in the ring!
cfg error : more than one rm There is more than
one RM in the ring.
More than one RM in
the ring.
Check the device
configuration. Only
one device may be
configured as the RM
in the ring!
cfg error : rm sw-version The firmware on the
RM is incompatible.
Incompatible software
versions of Observer
and RM devices
Check the software
version of the RM.
cfg error : rm on wrong port The RM is connected
to the wrong port of
the Observer.
Wiring error Connect the
Observer to the RM
as described in the
instructions.
rm timeout The Observer is no
longer receiving test
frames.
Device and/or wiring
fault/error
Check whether cable
and device function
correctly. Problem
indicators are the
traffic LEDs and the
statistics counters of
the ring ports.
(
1
): do not appear in the event log table.
(
2
): in the protection mode, in addition to the event log entry, port 7
(port 3 on the OSM TP22 ESM TP40) is set to passive
- Purpose of the Manual 6
- Scope of the Manual 6
- Notes for the Reader 7
- Finding Information 7
- Target Group 7
- Audience 8
- Further Support 9
- C79000-G8976-C137-08 10
- Introduction 13
- 1.1.1 Function 14
- Protocol 15
- Getting Information 15
- Making Settings 15
- 1.2.1 Signaling Concept 17
- 1.2.2 Network Management 17
- 1.3 Command Interpreter (CLI) 20
- 1.4 Setting the IP Addresses 20
- Important OSM/ESM Functions 21
- 2.1 Autonegotiation 22
- 2.2 Autocrossover 23
- Defaults 24
- Protected Settings 24
- Restore Factory Defaults 24
- 2.6 Locked Ports 28
- 2.7 Mirroring 29
- 2.8 Traps 30
- 2.9 E-Mail Function 31
- 2.10 Event Log Table 32
- 2.12 Flow Control 34
- 2.13 BOOTP/DHCP 35
- 2.15 TELNET 37
- Redundant Coupling 38
- 1 Fiber-optic cable (FO) 39
- 2 ITP XP standard cable 9/9 39
- 2.17 Observer Function 41
- Command Interpreter (CLI) 44
- 3.1 Overview 45
- 3.2 Password Protection 45
- 3.3 Installing the CLI 46
- 3.4 Login 47
- 3.5 CLI Commands 48
- CLI Menus and Description 49
- Start Menu 50
- System Menu 51
- Command CommentDescription 52
- OSM/ESM Menu 53
- Agent Menu 55
- Switch Menu 58
- Port Menu 60
- Service Menu 61
- Web-Based Management (WBM) 62
- 4.1 General Introduction 63
- 4.2 Requirements 64
- 4.3 Connecting 65
- Figure 4-2 “Login” Window 66
- Figure 4-3 WBM Startup Window 67
- Device Status Field 69
- Menu Tree 69
- Data Window 69
- 4.6 Management Menus 70
- 4.7 System 71
- 4.7.1 System Version Numbers 72
- Hardware 73
- Order Number 73
- Boot software 73
- Operative software 73
- MAC Address 73
- 4.7.2 System Restart 74
- 4.7.3 System Factory Defaults 75
- (restoring the defaults) 75
- 4.7.4 System Save & Load 76
- Log Table File 77
- Firmware File 77
- 4.7.5 Event Log Table 78
- 4.8 OSM/ESM Status 79
- Standby Status 80
- RM Status 80
- Power Line 1 80
- Power Line 2 80
- Fault Status 81
- 4.8.1 OSM/ESM Fault Mask 82
- Set New Values 83
- 4.8.2 OSM/ESM Standby Mask 84
- 4.8.3 OSM/ESM Counters 86
- 4.9 Agent Features 88
- E-Mail Address 92
- SMTP Server IP Address 92
- “From” Field 93
- 4.9.5 Agent ARP Table 95
- 4.9.6 Agent SNMP Counters 96
- 4.10 Switch Features 97
- Flow Control 98
- Set New Value 98
- 4.10.1 Current FDB Table 99
- Start with MAC 100
- Clear Address 100
- Next Values 100
- 4.10.2 Static FDB Table 101
- Entering a Multicast Address 105
- 4.11 Port Status 106
- Flow Ctrl 107
- 4.11.1 Port Configuration 108
- 4.12 Statistics Counters 110
- 4.12.1 Packet Size 111
- 4.12.2 Packet Type 112
- 4.12.3 Packet Error 113
- SNMP and RMON 114
- 5.1 SNMP 115
- 5.2 RMON 116
- 6.1 General Introduction 118
- Figure 6-1 119
- Figure 6-2 120
- Figure 6-3 120
- Figure 6-4 121
- Requirements 122
- Notes on Troubleshooting 124
- Internet Browser Settings 128
- Figure A-2 Trusted Sites 130
- A.2 Netscape Communicator 6.2 138
- Serial Port of the OSM/ESM 140
- Figure B-1 Properties Tab 142
- References 143
- Abbreviations/Acronyms 145
- Glossary 148
Verwandte Produkte und Handbücher für Vernetzung Siemens OSM
Vernetzung Siemens OSM Betriebsanleitung
(98 Seiten)
(98 Seiten)
Vernetzung Siemens CP 1515 Wartungshandbuch
(15 Seiten)
(15 Seiten)
Vernetzung Siemens CL-010 Bedienungsanleitung
(22 Seiten)
(22 Seiten)
Vernetzung Siemens SL2-141 Bedienungsanleitung
(24 Seiten)
(24 Seiten)
Vernetzung Siemens 2614 Betriebsanweisung
(44 Seiten)
(44 Seiten)
Vernetzung Siemens 5890 Bedienungsanleitung
(18 Seiten)
(18 Seiten)
Vernetzung Siemens PSFR-CP41 Spezifikationen
(81 Seiten)
(81 Seiten)
Vernetzung Siemens SE105 Spezifikationen
(115 Seiten)
(115 Seiten)
Vernetzung Siemens SPC3 Bedienungsanleitung
(11 Seiten)
(11 Seiten)
Vernetzung Siemens DTU3005-B Spezifikationen
(88 Seiten)
(88 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.067 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern