Siemens SED2 Wartungshandbuch Seite 12
- Seite / 154
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
SED2 Operation & Maintenance Manual
4 Siemens Building Technologies, Inc.
Repair
Only Siemens service departments, repair centers authorized by Siemens Building Technologies,
or authorized personnel who are fully acquainted with the SED2 may repair this equipment.
Replace defective parts or components using original manufacturer parts.
DANGER:
Always disconnect the power source before opening the SED2.
Environmental Compatibility and Disposal
The SED2 drives are developed and manufactured using materials and processes which take full
account of environmental issues and which comply with environmental standards. For disposal at
the end of the SED2 drive service life or in the event of its replacement, note the following:
• For disposal purposes, this product is defined as waste derived from electrical and electronic
equipment (“electronic waste”) and must not be disposed of as household waste. This applies
particularly to the PCB assembly.
• Always use the most environmentally compatible method of disposal, in line with the latest
developments in environmental protection, recycling, and waste management. Observe all
local legislation and applicable laws.
• Always aim for maximum re-use of the basic materials, and minimum environmental stress.
Observe any notes about materials and disposal that may be attached to individual
components.
• Use local depots and waste management companies, or See your supplier or manufacturer
to return used products or to obtain further information on environmental compatibility and
waste disposal.
• Special handling of components such as electrolytic capacitors and LCD panels may in some
cases be compulsory by law or environmentally desirable.
• The SED2 is delivered in re-usable packaging. Please retain the packaging for later use or in
case you need to return the product to the manufacturer.
- SED2 Operation & 3
- Maintenance Manual 3
- Manual Organization 9
- Manual Notations 10
- Where To Send Comments 10
- Reference Documents 10
- General 11
- Environmental Conditions 13
- Frame Sizes and Power Ranges 14
- Mounting 15
- Frame Size B Frame Size C 17
- Motor Cable Length 19
- Torx driver T20 21
- Power and Motor Connections 22
- :$51,1* 23
- (Ground) 25
- Control Terminal Connections 28
- 5 1 9 2 B 0 1 e n 29
- Chapter 5 — Commissioning 30
- DIP Switch Settings 31
- Prerequisites 32
- SED2 Operator Panels 32
- Buttons on the BOP and AOP 33
- Chapter 5 – Commissioning 35
- Continued 35
- Commissioning Prerequisites 36
- LR 39020 37
- SED2 Operation with the BOP 41
- Testing with the BOP 42
- Testing with the AOP 42
- Chapter 6 — Programming 43
- See AOP 45
- Operating 45
- Instructions 45
- SED2 Basic Functions 46
- DIN6 DIN5 47
- DIN4 DIN3 47
- DIN2 DIN1 47
- Digital Outputs 48
- Analog Inputs 49
- Signal in % 50
- Time in ms 50
- Analog Outputs 51
- P0776, Type of analog output 52
- Frequency Setpoint (P1000) 53
- OFF Functions 54
- SED2 HVAC Functions 55
- CONTROLLER 56
- 5192Z22en 57
- 5192Z23de 59
- Staging Pumps or Fans 60
- Figure 35. Staging Pumps 61
- P2378, Staging frequency 64
- Control (Commissioning) 65
- Chapter 7 — Troubleshooting 67
- Chapter 7 – Troubleshooting 69
- Reading Faults 74
- Resetting Faults 74
- Warning Messages 74
- Chapter 8 — Technical Data 78
- Specification Options 78
- Dimensions and Weights 80
- Unit-specific Data 80
- Options 84
- Overview 85
- Using the Serial Interface 85
- Hardware Inputs and Outputs 86
- Point Database 87
- Ordering Notes 87
- Verifying Parameters 88
- Using the SED2 with SBT (P1) 88
- Strategies for FLN (P1) 88
- Other Functionality 90
- Chapter 9 – Communications 95
- N2 Bus Connections 96
- Inverter Unit (P0004=2) 99
- Motor Data (P0004=3) 100
- Analogue I/O (P0004=8) 101
- Drive Features (P0004=12) 103
- Motor Control (P0004=13) 103
- Communication (P0010=20) 104
- PI Controller (P0004=22) 105
- Factory settings (P0010=30) 106
- Parameter List 107
- Manual Addendum 137
- EMC-Compatibility 139
- 5192Z04en 140
- Shield connected 141
- Motor cable 141
- Incoming mains voltage 141
- 5192J21us 141
- Frame Sizes A through C 142
- Frame Sizes D through F 143
- Connecting Multiple Motors 144
- Chapter 3 - Programming 146
- (Bypass request) 147
- Bypass contactor 147
- VSD contactor 147
- Hibernation Mode 148
- P2392, Restart frequency 149
- Introduction 150
- How does BiCo work? 150
- 125-3202 154
Verwandte Produkte und Handbücher für Fernseher & Monitore Siemens SED2
Fernseher & Monitore Siemens NCM S7 Wartungshandbuch
(225 Seiten)
(225 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 1.141 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern