Siemens SED2 Wartungshandbuch Seite 132
- Seite / 154
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
SED2 Operation and Maintenance Manual
124 Siemens Building Technologies, Inc
P2240[2] Setpoint of PID-MOP
Min: -200.00 Def: 10.00 Max: 200.00
Level 2
Settings:
722.0=Digital input 1 (requires P0701 set to 99, BICO)
722.1=Digital input 2 (requires P0702 set to 99, BICO)
722.2=Digital input 3 (requires P0703 set to 99, BICO)
722.3=Digital input 4 (requires P0704 set to 99, BICO)
722.4=Digital input 5 (requires P0705 set to 99, BICO)
722.5=Digital input 6 (requires P0706 set to 99, BICO)
722.6=Digital input 7 (via analog input 1, requires P0707 set to 99)
722.7=Digital input 8 (via analog input 2, requires P0708 set to 99)
19.D =Keypad UP cursor
Dependency:
To change setpoint:
1. Use UP/DOWN key on BOP or
2. Set P0702/P0703=13/14 (function of digital inputs 2 and 3)
Note:
P2240=100% corresponds to 4000 hex.
r2250 CO: Output setpoint of PID-MOP
Min: - Def: - Max: -
Level 2
Note:
r2250=100% corresponds to 4000 hex.
P2253[2] CI: PID setpoint
Min: 0:0 Def: 0:0 Max: 4000:0
Level 2
Details:
This parameter allows you to select the source of the PID setpoint. Normally, a digital setpoint is selected either using a
fixed PID setpoint or an active setpoint.
Settings:
755= Analog input 1 2224 =Fixed PI setpoint (see P2201 to P2207) 2250 =Active PI setpoint (see P2240)
Index;
P2253[0] : IN000 (AUTO) 1st. Command data set (CDS) P2253[1] : IN001 (HAND) 2nd. Command data set (CDS)
P2254[2] CI: PID trim source
Min: 0:0 Def: 0:0 Max: 4000:0
Level 3
Details:
This parameter allows you to select the source of the PID setpoint. Normally, a digital setpoint is selected either using a
fixed PID setpoint or an active setpoint.
Settings:
755= Analog input 1 2224 =Fixed PI setpoint (see P2201 to P2207) 2250 =Active PI setpoint (see P2240)
Index:
P2254[0] : IN000 (AUTO) 1st. Command data set (CDS) P2254[1] : IN001 (HAND) 2nd. Command data set (CDS)
P2261 PID setpoint filter time constant
Min: 0.00 Def: 0.00 Max: 60.00
Level 3
Note:
0=no smoothing
r2262 CO: Act. PID filtered setpoint
Min: - Def: - Max: -
Level 2
Details:
Displays PID setpoint in [%] after smoothing.
Note:
r2262=100% corresponds to 4000 hex.
P2264[2] CI: PID feedback
Min: 0:0 Def: 755:0 Max: 4000:0
Level 2
Settings:
755= Analog input 1 setpoint 2224 =Fixed PID setpoint 2250 =Output setpoint of PID-MOP
Index:
P2264[0] : IN000 (AUTO) 1st. Command data set (CDS) P2264[1] : IN001 (HAND) 2nd. Command data set (CDS)
Note:
When analog input is selected, offset and gain can be implemented using parameters P0756 to P0760.
P2265 PID feedback filter timeconstant
Min: 0.00 Def: 0.00 Max: 60.00
Level 2
P2267 Max. value for PID feedback
Min: -200.00 Def: 100.00 Max: 200.00
Level 3
Note:
P2267=100% corresponds to 4000 hex.
When PID is enabled (P2200=1) and the signal rises above this value, the inverter will trip with P0222.
P2268 Min. value for PID feedback
Min: -200.00 Def: 0.00 Max: 200.00
Level 3
Note:
P2268=100% corresponds to 4000 hex.
When PID is enabled (P2200=1) and the signal rises above this value, the inverter will trip with P0221.
P2269 Gain applied to PID feedback
Min: 0.00 Def: 100.00 Max: 500.00
Level 3
Note:
Allows you to scale the PID feedback as a percentage value [%].
A gain of 100.0% means that feedback signal has not changed from its default value.
- SED2 Operation & 3
- Maintenance Manual 3
- Manual Organization 9
- Manual Notations 10
- Where To Send Comments 10
- Reference Documents 10
- General 11
- Environmental Conditions 13
- Frame Sizes and Power Ranges 14
- Mounting 15
- Frame Size B Frame Size C 17
- Motor Cable Length 19
- Torx driver T20 21
- Power and Motor Connections 22
- :$51,1* 23
- (Ground) 25
- Control Terminal Connections 28
- 5 1 9 2 B 0 1 e n 29
- Chapter 5 — Commissioning 30
- DIP Switch Settings 31
- Prerequisites 32
- SED2 Operator Panels 32
- Buttons on the BOP and AOP 33
- Chapter 5 – Commissioning 35
- Continued 35
- Commissioning Prerequisites 36
- LR 39020 37
- SED2 Operation with the BOP 41
- Testing with the BOP 42
- Testing with the AOP 42
- Chapter 6 — Programming 43
- See AOP 45
- Operating 45
- Instructions 45
- SED2 Basic Functions 46
- DIN6 DIN5 47
- DIN4 DIN3 47
- DIN2 DIN1 47
- Digital Outputs 48
- Analog Inputs 49
- Signal in % 50
- Time in ms 50
- Analog Outputs 51
- P0776, Type of analog output 52
- Frequency Setpoint (P1000) 53
- OFF Functions 54
- SED2 HVAC Functions 55
- CONTROLLER 56
- 5192Z22en 57
- 5192Z23de 59
- Staging Pumps or Fans 60
- Figure 35. Staging Pumps 61
- P2378, Staging frequency 64
- Control (Commissioning) 65
- Chapter 7 — Troubleshooting 67
- Chapter 7 – Troubleshooting 69
- Reading Faults 74
- Resetting Faults 74
- Warning Messages 74
- Chapter 8 — Technical Data 78
- Specification Options 78
- Dimensions and Weights 80
- Unit-specific Data 80
- Options 84
- Overview 85
- Using the Serial Interface 85
- Hardware Inputs and Outputs 86
- Point Database 87
- Ordering Notes 87
- Verifying Parameters 88
- Using the SED2 with SBT (P1) 88
- Strategies for FLN (P1) 88
- Other Functionality 90
- Chapter 9 – Communications 95
- N2 Bus Connections 96
- Inverter Unit (P0004=2) 99
- Motor Data (P0004=3) 100
- Analogue I/O (P0004=8) 101
- Drive Features (P0004=12) 103
- Motor Control (P0004=13) 103
- Communication (P0010=20) 104
- PI Controller (P0004=22) 105
- Factory settings (P0010=30) 106
- Parameter List 107
- Manual Addendum 137
- EMC-Compatibility 139
- 5192Z04en 140
- Shield connected 141
- Motor cable 141
- Incoming mains voltage 141
- 5192J21us 141
- Frame Sizes A through C 142
- Frame Sizes D through F 143
- Connecting Multiple Motors 144
- Chapter 3 - Programming 146
- (Bypass request) 147
- Bypass contactor 147
- VSD contactor 147
- Hibernation Mode 148
- P2392, Restart frequency 149
- Introduction 150
- How does BiCo work? 150
- 125-3202 154
Verwandte Produkte und Handbücher für Fernseher & Monitore Siemens SED2
Fernseher & Monitore Siemens NCM S7 Wartungshandbuch
(225 Seiten)
(225 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 1.223 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern