Siemens SED2 Wartungshandbuch Seite 71
- Seite / 154
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Chapter 7 – Troubleshooting
Siemens Building Technologies, Inc. 63
Error Cause Diagnosis/Remedy Reaction
F0041, Motor
data identification
failure
• Motor data identification
failed
• Alarm value = 0: Load is
missing
• Alarm value = 1: Current
limit value reached during
identification.
• Alarm value = 2: Identified
stator resistance less than
0.1% or more than 100%.
• Alarm value = 3: Identified
rotor resistance less than
0.1% or more than 100%.
• Alarm value = 4: Identified
stator reactance less than
50% or more than 500%.
• Alarm value = 5: Identified
main reactance less than
50% or more than 500%.
• Alarm value = 6: Identified
rotor time constant less than
10 ms or more than 5s.
• Alarm value = 7: Identified
total leakage reactance less
than 5% or more than 50%.
• Alarm value = 8: Identified
stator leakage reactance
less than 25% or more than
250%.
• Alarm value = 9: Identified
rotor leakage reactance less
than 25% or more than
250%.
• Alarm value = 20: Identified
IGBT ON-voltage less than
0.5 or more than 10V.
• Alarm value = 30: Current
controller at voltage limit.
• Alarm value = 40:
Inconsistency of identified
data set, at least one
identification failed.
Percentage values based on
impedance
Zb = Vmot,nom / sqrt(3) /
Imot,nom.
0: Check if the motor is
connect to the SED2.
1-40: Check if the motor data in
P0304 to P0311 are correct.
Check the type of motor wiring
required (star, delta).
Off2
- SED2 Operation & 3
- Maintenance Manual 3
- Manual Organization 9
- Manual Notations 10
- Where To Send Comments 10
- Reference Documents 10
- General 11
- Environmental Conditions 13
- Frame Sizes and Power Ranges 14
- Mounting 15
- Frame Size B Frame Size C 17
- Motor Cable Length 19
- Torx driver T20 21
- Power and Motor Connections 22
- :$51,1* 23
- (Ground) 25
- Control Terminal Connections 28
- 5 1 9 2 B 0 1 e n 29
- Chapter 5 — Commissioning 30
- DIP Switch Settings 31
- Prerequisites 32
- SED2 Operator Panels 32
- Buttons on the BOP and AOP 33
- Chapter 5 – Commissioning 35
- Continued 35
- Commissioning Prerequisites 36
- LR 39020 37
- SED2 Operation with the BOP 41
- Testing with the BOP 42
- Testing with the AOP 42
- Chapter 6 — Programming 43
- See AOP 45
- Operating 45
- Instructions 45
- SED2 Basic Functions 46
- DIN6 DIN5 47
- DIN4 DIN3 47
- DIN2 DIN1 47
- Digital Outputs 48
- Analog Inputs 49
- Signal in % 50
- Time in ms 50
- Analog Outputs 51
- P0776, Type of analog output 52
- Frequency Setpoint (P1000) 53
- OFF Functions 54
- SED2 HVAC Functions 55
- CONTROLLER 56
- 5192Z22en 57
- 5192Z23de 59
- Staging Pumps or Fans 60
- Figure 35. Staging Pumps 61
- P2378, Staging frequency 64
- Control (Commissioning) 65
- Chapter 7 — Troubleshooting 67
- Chapter 7 – Troubleshooting 69
- Reading Faults 74
- Resetting Faults 74
- Warning Messages 74
- Chapter 8 — Technical Data 78
- Specification Options 78
- Dimensions and Weights 80
- Unit-specific Data 80
- Options 84
- Overview 85
- Using the Serial Interface 85
- Hardware Inputs and Outputs 86
- Point Database 87
- Ordering Notes 87
- Verifying Parameters 88
- Using the SED2 with SBT (P1) 88
- Strategies for FLN (P1) 88
- Other Functionality 90
- Chapter 9 – Communications 95
- N2 Bus Connections 96
- Inverter Unit (P0004=2) 99
- Motor Data (P0004=3) 100
- Analogue I/O (P0004=8) 101
- Drive Features (P0004=12) 103
- Motor Control (P0004=13) 103
- Communication (P0010=20) 104
- PI Controller (P0004=22) 105
- Factory settings (P0010=30) 106
- Parameter List 107
- Manual Addendum 137
- EMC-Compatibility 139
- 5192Z04en 140
- Shield connected 141
- Motor cable 141
- Incoming mains voltage 141
- 5192J21us 141
- Frame Sizes A through C 142
- Frame Sizes D through F 143
- Connecting Multiple Motors 144
- Chapter 3 - Programming 146
- (Bypass request) 147
- Bypass contactor 147
- VSD contactor 147
- Hibernation Mode 148
- P2392, Restart frequency 149
- Introduction 150
- How does BiCo work? 150
- 125-3202 154
Verwandte Produkte und Handbücher für Fernseher & Monitore Siemens SED2
Fernseher & Monitore Siemens NCM S7 Wartungshandbuch
(225 Seiten)
(225 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.278 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern