Siemens AC75 Bedienungsanleitung Seite 258
- Seite / 569
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
AC75 AT Command Set
10.1 AT^SICS
s
AC75_ATC_V01.002 Page 258 of 569 10/30/06
Confidential / Released
“authMode“ Authentication mode.
For supported values of <conParmValue> refer to <conParmValue-auth-
Mode>.
“fnur“ Fixed Network User Rate.
For supported values of <conParmValue> refer to <conParmValue-fnur>.
“dns1“ Primary DNS server address (IP address in dotted-four-byte format).
This value determines whether to use the DNS server addresses dynamically
assigned by the network or a specific DNS server address given by the user.
"dns1" = "0.0.0.0" (default) means that the CSD or GPRS connection profile
uses dynamic DNS assignment. Any other address means that the Primary
DNS is manually set.
The default value applies automatically if no other address is set. Note that the
AT^SICS read command only returns a manually configured IP address, while
the value "0.0.0.0" is not indicated at all, no matter whether assumed by default
or explicitly specified.
See also note below.
“dns2“ Secondary DNS server address (IP address in dotted-four-byte format).
If "dns1" = "0.0.0.0" this setting will be ignored. Otherwise this value can be
used to manually configure an alternate server for the DNS1.
If "dns1" is not equal "0.0.0.0" and no "dns2" address is given, then
"dns2"="0.0.0.0" will be assumed automatically. The AT^SICS read command
only returns a manually configured IP address, while the value "0.0.0.0" is not
indicated at all, no matter whether assumed by default or explicitly specified.
Parameter value; type and supported content depend on related <conParmTag>.
Supported connection type values in <conParmValue> for <conParmTag> value "conType".
“CSD“ Circuit-switched data call.
“GPRS0“ GPRS connection.
Settings of GPRS related commands are not used, e.g. AT+CGDCONT. When a
service based on a GPRS connection profile is started after entering AT^SISO
AC75 automatically tries to attach to the GPRS. Yet, the only exception is
AT+CGATT which can be used any time to detach from the GPRS and, and thus
disconnect the bearer opened with AT^SISO.
“none“ Clears the connection profile.
Character set selectable with <conParmValue> for <conParmTag> value "alphabet".
[“0“] Character set determined with AT+CSCS applies.
“1“ International Reference Alphabet (IRA, seven bit ASCII) applies.
Supported data rate values in <conParmValue> for <conParmTag> value "dataRate".
“0“ 14.4 KBaud
[“1“] 9.6 KBaud
<conParmValue>
(str)
<conParmValue-conType>
(str)
<conParmValue-alphabet>
(str)
<conParmValue-dataRate>
(str)
- AT Command Set 1
- Contents 3
- AC75 AT Command Set 10
- List of Tables 12
- List of Figures 13
- 1. Introduction 14
- 1.2 Related documents 15
- 1.3 Document conventions 16
- 1.3.1 Quick reference table 16
- 1.4 AT Command Syntax 18
- 1.4.1 Using Parameters 18
- 1.5 Supported character sets 20
- 1.10 Errors and Messages 31
- 2. Configuration Commands 32
- 2.2.1 AT&V responses 34
- 3. Status Control Commands 80
- 3.2 AT+CIND Indicator control 82
- 3.4.2 SIEMENS L2 cause 94
- Management (SM) 95
- 4.1 AT\Q Flow control 105
- 4.5 ATE Enable command echo 109
- 4.9.1 Autobauding 117
- 5. Security Commands 124
- 5.4 AT+CLCK Facility lock 134
- 5.5 AT^SLCK Facility lock 139
- 5.6 AT+CPWD Change Password 140
- 5.7 AT^SPWD Change Password 144
- 5.8 AT^SCSL Customer SIM Lock 146
- 6. Identification Commands 150
- 7. Call related Commands 156
- 7.2 ATA Answer a call 157
- 7.10 AT+CHUP Hang up call 167
- 7.29 ATP Select pulse dialing 193
- 7.30 ATT Select tone dialing 193
- 8. Network Service Commands 194
- 8.5 AT+CSQ Signal quality 203
- 8.6 AT^SMONC Cell Monitoring 204
- 8.7 AT^SMOND Cell Monitoring 206
- 8.9.1 AT^MONI responses 211
- 8.9.2 Service states 212
- 8.10.1 AT^MONP responses 214
- 8.11 AT^SMONG GPRS Monitor 215
- 8.13 AT^SHOM Display Homezone 219
- 9.5 AT+CCUG Closed User Group 230
- 9.7 AT+CCWA Call Waiting 236
- 10. Internet Service Commands 253
- 10.11.1 Example: Ping 292
- Another Host 299
- 11. GPRS Commands 308
- 12. FAX Commands 352
- 12.4 AT+FRM Receive Data 355
- 12.5 AT+FRS Receive Silence 356
- 12.7 AT+FTM Transmit Data 358
- 13.1 SMS parameters 360
- 14. SIM related Commands 402
- 15.3 Related AT Commands 426
- 16.2 ^SSTN SAT Notification 430
- 16.4 AT^SSTR SAT Response 432
- 17. Phonebook Commands 433
- 17.2 AT+CNUM Read own numbers 434
- 18. Audio Commands 456
- 18.5 AT+CMUT Mute control 459
- 18.6 AT+VTD Tone duration 460
- 19. Hardware Related Commands 481
- 19.2 AT+CALA Set alarm time 482
- 19.3 AT^SAD Antenna Diagnosis 485
- 19.6.1 Deferred shutdown 492
- 19.8.2 Selecting SPI Mode 499
- 19.8.5 Example: Using I²C Bus 504
- 20. GPIO Commands 508
- 21. Java related Commands 521
- 22. Miscellaneous Commands 529
- 23. Appendix 535
Verwandte Produkte und Handbücher für Mobiltelefone Siemens AC75
Mobiltelefone Siemens C62 Bedienungsanleitung
(69 Seiten)
(69 Seiten)
Mobiltelefone Siemens SXG75 Bedienungsanleitung
(166 Seiten)
(166 Seiten)
Mobiltelefone Siemens A35 Bedienungsanleitung
(43 Seiten)
(43 Seiten)
Mobiltelefone Siemens M30 Bedienungsanleitung
(31 Seiten)
(31 Seiten)
Mobiltelefone Siemens CXT65 Bedienungsanleitung
(141 Seiten)
(141 Seiten)
Mobiltelefone Siemens S56 Bedienungsanleitung
(152 Seiten)
(152 Seiten)
Mobiltelefone Siemens AX75 Bedienungsanleitung
(28 Seiten)
(28 Seiten)
Mobiltelefone Siemens C30 Bedienungsanleitung
(31 Seiten)
(31 Seiten)
Mobiltelefone Siemens MC60 Bedienungsanleitung
(118 Seiten)
(118 Seiten)
Mobiltelefone Siemens CX70 Bedienungsanleitung
(74 Seiten)
(74 Seiten)
Mobiltelefone Siemens GSM 900 Bedienungsanleitung
(115 Seiten)
(115 Seiten)
Mobiltelefone Siemens A60 Bedienungsanleitung
(62 Seiten)
(62 Seiten)
Mobiltelefone Siemens S40 Bedienungsanleitung
(50 Seiten)
(50 Seiten)
Mobiltelefone Siemens SL75 Bedienungsanleitung
(139 Seiten)
(139 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 1.149 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern