Siemens AC75 Bedienungsanleitung Seite 496
- Seite / 569
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
AC75 AT Command Set
19.8 AT^SSPI
s
AC75_ATC_V01.002 Page 496 of 569 10/30/06
Confidential / Released
19.8 AT^SSPI Serial Protocol Interface
The AT^SSPI command enables the module to be connected to external I²C or SPI devices.
The I²C/SPI datastream is mapped through an internal I²C/SPI driver to and from an ASCII hex protocol which
can be exchanged with an internal application (JAVA) or an external application via V24.
The AT^SSPI write command configures and activates the I²C/SPI interface and changes from command mode
into data mode. All values must be given in hexadecimal format (0 - 9, A - F) without "0x". For details on data
mode please refer to Section 19.8.3, Transmitting Data over AT Interface.
Caution:
I²C and SPI cannot be operated in parallel with USB. The USB interface will be disabled as soon as the I²C or
SPI channel is opened with AT^SSPI. To activate the USB interface again after closing the I²C or SPI channel
it is necessary to restart the AC75 module, either by switching the ignition line or entering the command
AT+CFUN=1,1. The Terminal program or host application connected with the USB interface must be closed
before activating the USB.
If I²C or SPI data mode is active the DCD line of the connected serial port goes high.
If I²C or SPI are opened from a Java application be sure to close the I²C or SPI channels before Java terminates.
Syntax
Test Command
AT^SSPI=?
Response(s)
^SSPI:(list of supported <basicConfiguration>s), (list of supported <delayOne>s), (list of supported
<delayTwo>s), (list of supported <wordLength>s), (list of supported <extendedSpiConfiguration>s)
OK
Read Command
AT^SSPI?
Response(s)
^SSPI: <connectionState>, <basicConfiguration>, <delayOne>, <delayTwo>, <wordLength>,
<extendedSpiConfiguration>
OK
ERROR
+CME ERROR: <err>
Write Command
AT^SSPI=[<basicConfiguration>[, <delayOne>[, <delayTwo>[, <wordLength>[,
<extendedSpiConfiguration>]]]]]
Response(s)
CONNECT
(indicates that ME has entered data mode)
ERROR
+CME ERROR: <err>
Reference(s) PIN ASC0 ASC1 USB MUX1 MUX2 MUX3 Charge 4 Last
SIEMENS - + + - + + + - + +
- AT Command Set 1
- Contents 3
- AC75 AT Command Set 10
- List of Tables 12
- List of Figures 13
- 1. Introduction 14
- 1.2 Related documents 15
- 1.3 Document conventions 16
- 1.3.1 Quick reference table 16
- 1.4 AT Command Syntax 18
- 1.4.1 Using Parameters 18
- 1.5 Supported character sets 20
- 1.10 Errors and Messages 31
- 2. Configuration Commands 32
- 2.2.1 AT&V responses 34
- 3. Status Control Commands 80
- 3.2 AT+CIND Indicator control 82
- 3.4.2 SIEMENS L2 cause 94
- Management (SM) 95
- 4.1 AT\Q Flow control 105
- 4.5 ATE Enable command echo 109
- 4.9.1 Autobauding 117
- 5. Security Commands 124
- 5.4 AT+CLCK Facility lock 134
- 5.5 AT^SLCK Facility lock 139
- 5.6 AT+CPWD Change Password 140
- 5.7 AT^SPWD Change Password 144
- 5.8 AT^SCSL Customer SIM Lock 146
- 6. Identification Commands 150
- 7. Call related Commands 156
- 7.2 ATA Answer a call 157
- 7.10 AT+CHUP Hang up call 167
- 7.29 ATP Select pulse dialing 193
- 7.30 ATT Select tone dialing 193
- 8. Network Service Commands 194
- 8.5 AT+CSQ Signal quality 203
- 8.6 AT^SMONC Cell Monitoring 204
- 8.7 AT^SMOND Cell Monitoring 206
- 8.9.1 AT^MONI responses 211
- 8.9.2 Service states 212
- 8.10.1 AT^MONP responses 214
- 8.11 AT^SMONG GPRS Monitor 215
- 8.13 AT^SHOM Display Homezone 219
- 9.5 AT+CCUG Closed User Group 230
- 9.7 AT+CCWA Call Waiting 236
- 10. Internet Service Commands 253
- 10.11.1 Example: Ping 292
- Another Host 299
- 11. GPRS Commands 308
- 12. FAX Commands 352
- 12.4 AT+FRM Receive Data 355
- 12.5 AT+FRS Receive Silence 356
- 12.7 AT+FTM Transmit Data 358
- 13.1 SMS parameters 360
- 14. SIM related Commands 402
- 15.3 Related AT Commands 426
- 16.2 ^SSTN SAT Notification 430
- 16.4 AT^SSTR SAT Response 432
- 17. Phonebook Commands 433
- 17.2 AT+CNUM Read own numbers 434
- 18. Audio Commands 456
- 18.5 AT+CMUT Mute control 459
- 18.6 AT+VTD Tone duration 460
- 19. Hardware Related Commands 481
- 19.2 AT+CALA Set alarm time 482
- 19.3 AT^SAD Antenna Diagnosis 485
- 19.6.1 Deferred shutdown 492
- 19.8.2 Selecting SPI Mode 499
- 19.8.5 Example: Using I²C Bus 504
- 20. GPIO Commands 508
- 21. Java related Commands 521
- 22. Miscellaneous Commands 529
- 23. Appendix 535
Verwandte Produkte und Handbücher für Mobiltelefone Siemens AC75
Mobiltelefone Siemens C62 Bedienungsanleitung
(69 Seiten)
(69 Seiten)
Mobiltelefone Siemens SXG75 Bedienungsanleitung
(166 Seiten)
(166 Seiten)
Mobiltelefone Siemens A35 Bedienungsanleitung
(43 Seiten)
(43 Seiten)
Mobiltelefone Siemens M30 Bedienungsanleitung
(31 Seiten)
(31 Seiten)
Mobiltelefone Siemens CXT65 Bedienungsanleitung
(141 Seiten)
(141 Seiten)
Mobiltelefone Siemens S56 Bedienungsanleitung
(152 Seiten)
(152 Seiten)
Mobiltelefone Siemens AX75 Bedienungsanleitung
(28 Seiten)
(28 Seiten)
Mobiltelefone Siemens C30 Bedienungsanleitung
(31 Seiten)
(31 Seiten)
Mobiltelefone Siemens MC60 Bedienungsanleitung
(118 Seiten)
(118 Seiten)
Mobiltelefone Siemens CX70 Bedienungsanleitung
(74 Seiten)
(74 Seiten)
Mobiltelefone Siemens GSM 900 Bedienungsanleitung
(115 Seiten)
(115 Seiten)
Mobiltelefone Siemens A60 Bedienungsanleitung
(62 Seiten)
(62 Seiten)
Mobiltelefone Siemens S40 Bedienungsanleitung
(50 Seiten)
(50 Seiten)
Mobiltelefone Siemens SL75 Bedienungsanleitung
(139 Seiten)
(139 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.263 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern