Siemens SINUMERIK 802D sl Wartungshandbuch Seite 86
- Seite / 130
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Manual machining
5.4 Manual machining using cycles (functions)
Manual Machine Plus Turning
86 Programming and Operating Manual, 06/2009, 6FC5398-6CP10-1BA0
Parameter Description
Chamfer/radius F1 Depending on the option selected, this value forms either a transition radius
(display "RND") or a transition chamfer (display "Chamfer CHR" or "Chamfer CHF")
of less than 45
0
between the end face and the inside diameter of the "step". You
can toggle between RND / CHR / CHF using the toggle key. An input value of 0.0
switches this function off.
Two types of dimensioning are possible with the chamfers:
• in the case of chamfer CHR, the value specifies the width of the chamfer in the
direction of the movement,
• in the case of chamfer CHF, the value corresponds with the length of the
chamfer.
Chamfer/radius F2 Depending on the option selected, this value forms either a transition radius
(display "RND") or a transition chamfer (display "Chamfer CHR" or "Chamfer CHF")
of less than 45
0
between the end face and the inside diameter of the "step". You
can toggle between RND / CHR / CHF using the toggle key. An input value of 0.0
switches this function off.
Two types of dimensioning are possible with the chamfers:
• in the case of chamfer CHR, the value specifies the width of the chamfer in the
direction of the movement,
• in the case of chamfer CHF, the value corresponds with the length of the
chamfer.
Chamfer/radius F3 Depending on the option selected, this value forms either a transition radius
(display "RND") or a transition chamfer (display "Chamfer CHR" or "Chamfer CHF")
of less than 45
0
between the end face and the inside diameter of the "step". You
can toggle between RND / CHR / CHF using the toggle key. An input value of 0.0
switches this function off.
Two types of dimensioning are possible with the chamfers:
• in the case of chamfer CHR, the value specifies the width of the chamfer in the
direction of the movement,
• in the case of chamfer CHF, the value corresponds with the length of the
chamfer.
Max. infeed depth m1 Enter the maximum infeed depth for roughing. The internal infeed calculation
ensures that the infeed is as uniform as possible throughout the roughing operation.
This entry value represents the maximum value possible and is therefore not
exceeded.
Finishing allowance m2 Finishing allowance in the X axis (m2x)
Finishing allowance in the Z axis (m2z)
The following possibilities exist for the position of the geometry:
- SINUMERIK 1
- SINUMERIK 802D sl 1
- Manual Machine Plus Turning 1
- Legal information 2
- Foreword 3
- Technical support 4
- SINUMERIK Internet address 4
- Foreword 5
- Table of contents 7
- Reference 10
- Description 11
- Hot keys 12
- Description 14
- Software interface 15
- 0DQXDOO\ 18
- &1& 18
- Requirement 19
- Operating sequence 20
- 3.2 Reference point approach 22
- Setting-up 23
- Setting-up 25
- 4.1 Measuring tools 25
- 4.2 Limit stops 26
- Parameter 27
- OLPLWVWRS 28
- Example: 29
- 4.2 Limit stops 30
- Additional information 31
- 'HOHWH 32
- Machine Plus" 34
- 5.2.1 Toggling the display 38
- 5.2.6 Tool change 41
- 0DFKLQHG 47
- 5.3.3 Manual radius turning 49
- 'ULOOLQJ 55
- D[LVSRV 55
- 5.4.2 General parameters 58
- 5.4.4 Manual thread tapping 62
- Tapping operation 64
- Groove cycle - single 67
- Multiple grooves 69
- Parting 70
- 5.4.5.4 Multiple tapping 70
- Multiple tapping 71
- 5.4.5.5 Extended grooving 71
- ([WHQGHG 72
- Extended grooving 74
- 5.4.6 Manual thread cutting 76
- 5.4.6.1 Thread cutting 77
- UHFXWWLQJ 80
- Execute thread recut 82
- 5.4.7 Roughing cycles 84
- 5RXJKLQJ 85
- F\FOH& 91
- F\FOH' 94
- &XWWLQJ 99
- Input fields 100
- Functionality 101
- Operating sequences 101
- ([WHUQDO 102
- FRQWRXUV 102
- &\FOH 102
- RYHUYLHZ 102
- Manual machining 103
- References 104
- Rough cutting 105
- Finish cutting 105
- See also 105
- Manual machining 106
- Screen handling functions 108
- Softkeys 108
- 7HDFK,Q 110
- 6.2 Teach In 114
- 6.2 Teach In 115
- 6.3 Simulate machining 117
- &RQWRXU 118
- VLPXODWLRQ 118
- Messages 123
- 7.1 Messages 124
- Appendix 125
- Appendix 127
Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme Siemens SINUMERIK 802D sl
(116 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.041 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern