Siemens v1.0 Wartungshandbuch Seite 163
- Seite / 202
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Example "PID control"
4.9 Active PID controller in online mode
STEP 7 Basic V10.5
Getting Started, 12/2009, A5E02651459-01
163
4. Perform a fine-tuning of the controller optimization, by starting the tuning in run.
The self-tuning starts. The current work steps and any errors that occur are shown in the
"Status" field. The progress bar shows the progress of the current work step. Several
steps are required for controller optimization. The progress display will start at "0" for
each step. If the self-tuning was completed without error message, the PID parameters
have been optimized. The PID controller switches to automatic mode and uses the
optimized parameters.
5. Monitor the curve shape in the top section of the "Commissioning" window.
Note
Shape of the curve
In time the shape of the curve gets closer and closer to the setpoint. To monitor the
complete shape of the curve, use the vertical scroll bar in the bottom area of the graphic
display.
After the controller has switched to automatic mode, the controller reacts to the
temperature changes simulated by the "PROC_C" block by automatically adjusting the
controlled variable.
- SIMATIC 1
- TIA Portal 1
- STEP 7 Basic V10.5 1
- Legal information 2
- Table of contents 3
- 1.1 Overview 6
- 1.2 TIA Portal basics 7
- 7,$3RUWDO 8
- 8QLIRUPHQJLQHHULQJV\VWHP 8
- :LQ&&%DVLF9 8
- 67(3%DVLF9 8
- 1.2.3 Data management 9
- Library concept 10
- 1.3 Views in the TIA portal 11
- 1.3.2 Portal view 12
- 1.3.3 Project view 13
- TIA Portal Introduction 14
- 1.3 Views in the TIA portal 14
- 1.4 Example projects 15
- 1.4 Example projects 16
- 1.4.2 Loading a project 17
- TIA Portal Introduction 19
- 1.4 Example projects 19
- Simple example 21
- 2.3.1 Inserting a PLC 23
- Simple example 25
- Network view 26
- Device view 28
- 2.3.3 Configure PLC 29
- 2.4 Create program 31
- 2.4 Create program 33
- 2.4 Create program 34
- 2.4.4 What are networks? 35
- LAD instructions 36
- Normally open contact 37
- Negated coil 38
- 2.4.6 What are tags? 42
- PLC tag table 44
- 2.5 Test program 48
- 2.5 Test program 50
- 2.5 Test program 51
- Additional information 53
- +0, 3/& 3URFHVV 57
- Adding a new HMI device 58
- 2.6 Create HMI screen 59
- 2.6 Create HMI screen 60
- Graphic objects 65
- Use of graphic objects 65
- External HMI tags 66
- Internal HMI tags 77
- 2.7 Testing HMI screen 85
- 2.7.2 Simulate runtime 87
- 2.7 Testing HMI screen 88
- 3.1 Introduction 90
- 3.2 Expanding the program 91
- Normally closed contact 97
- Extended example 100
- 3.2 Expanding the program 100
- 2SHUDQG! 101
- Procedure 102
- Requirements 103
- Introduction 103
- Extended example 105
- 3.2 Expanding the program 105
- On delay 110
- Output coil 110
- 3.4 Expand HMI screen 123
- 3.4 Expand HMI screen 124
- 3.4 Expand HMI screen 129
- 3.5 Simulate HMI screen 132
- Testing in the HMI device 133
- 3.5 Simulate HMI screen 134
- 4.1 Introduction 135
- Use of the PID controller 136
- 4.1 Introduction 137
- STEP 7 Basic V10.5 140
- 4.4 Load simulation block 143
- 4.4 Load simulation block 144
- 4.4 Load simulation block 145
- 4.5 Configure PID controller 150
- Block name 151
- Parameter 151
- 4.8 Adjust HMI screen 158
- 4.8 Adjust HMI screen 159
- 4.8 Adjust HMI screen 160
- Controller optimization 161
- Example "Motion" 165
- Hardware configuration 166
- Example "Motion" 167
- 5.1 Introduction 167
- 5.4 Enable axis 173
- 5.4 Enable axis 174
- 5.4 Enable axis 175
- 5.5 Position axis relative 176
- 5.5 Position axis relative 177
- 5.5 Position axis relative 178
- 5.6 Expand HMI screen 180
- 5.6 Expand HMI screen 181
- 5.6 Expand HMI screen 184
- 5.7 Simulate HMI screen 189
- 5.7 Simulate HMI screen 190
- 5.8 Start diagnostics view 191
- 5.8 Start diagnostics view 192
- 5.8 Start diagnostics view 193
- Glossary 197
- Glossary 199
Verwandte Produkte und Handbücher für Software Siemens v1.0
Software Siemens 270 series Betriebsanleitung
(274 Seiten)
(274 Seiten)
Software Siemens S7-400 Wartungshandbuch
(382 Seiten)
(382 Seiten)
Software Siemens AC65 Betriebsanweisung
(123 Seiten)
(123 Seiten)
Software Siemens Simatic M7-400 Bedienungsanleitung
(266 Seiten)
(266 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.195 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern