Siemens KDN Series Betriebsanleitung Seite 107
- Seite / 258
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
KINCO
107
Bit Address Word Address PLC address Notes
X 00.000-00.047
X 0000-0047
Y 01.000-01.031
Y 0100-0131
WX 000.00-000.03 WX 0000-0003
WY 001.00-Y001.01 WY 0010-0011
Note:
The range of X, Y, WX, WY is according to the I/O assign. Make sure the I/O address before using the
register.
Note:
1. Communication setting
EH series, only port1 supports procedure 2.Switch DIP and change special Internal Input
(WR) value to select procedure.
EH150 series，only EHCPU***A/448/516/548 support procedure 2.
EH PLC connect with PC only by procedure 1.
2. CPU related actions
EH150
DIP 5 must be set on.
If DIP 5 is on, which procedure (1 or2) to use by judging the value of the WR F037.The
highest bit of WR F037 must be on, so that the other bits can be written in. The data keep on,
when turn on the power again.
o By entering 0x8000, turn on the power again and value of the address is 0x0000.After
settings, communication with procedure 1.
o By entering 0xC000, turn on the power again and value of the address is 0x4000.After
settings, communication with procedure 2.
The transmission speed of port 1 will be set with DIP 3, 4 switches
o 3 on, 4 off is 19200 bps
The transmission speed of port 2 will be set with DIP 6, PHL switches.
o 6 off, PHL on is 19200 bps
MicroEH
The transmission speed will be set with DIP switches
o SW1 on is 19200 bps
Which procedure(1 or2) to use by judging the value of the WR F01A.Different with EH150,
The highest bit of WR F01A is optional, The data will reset when turn on the power again. If the
value of R 7F6 is set on, the data of WR F01A will be stored in Flash memory.
o 0x0000 for procedure 1.
o 0x8000 for procedure 2.
Note: if procedure 2 is set and written in Flash memory, external device (only supports
procedure 1) or ladder editor will not connect with it.
Cable Diagram
Programming cable, as follow:
- CONTENTS 1
- Parallel Port Pin Definition 3
- Download Cable Diagram 10
- HMI Ethernet terminal 11
- Ethernet Hub or Switch 11
- RS232 12
- Allen-Bradley 14
- Serial System Communication 15
- Serial Communication Setting 16
- SLC500 RS232 communication 17
- PLC Software Setting 18
- Compactlogix L31 21
- PLC-5 RS232 cable diagram 23
- EtherNet cable 23
- ACS-Tech80 Motion Controller 24
- AysjNet 28
- Baumuller 33
- RS485-4 communication cable 33
- Bosch Rexroth 35
- PLC Software Settings 37
- L40 software setting 39
- Bosch Rexroth Ethernet 44
- Network communication 44
- CANOpen Node Slave 48
- Danfoss Inverter 55
- Frequency Converter 56
- Frequency Converter setting 56
- of process word: 57
- showed by RW register 57
- Modbus RTU Protocol: 58
- Delta Corporation 61
- DVP RS485-2 communication 62
- Controller Setting 65
- D3CellTM 71
- RS422 on the CPU unit 71
- DLoadCell 71
- EB-MOD2P-01(Bus Bridge) 72
- Emerson NetWork Power 79
- Facon Corporation 87
- Fuji SPB 91
- GE Fanuc Automation Inc 93
- HAIWELL 98
- Cable Diagram 100
- Serial Communication 100
- System configuration 100
- Communication Setting 100
- Supported Device 101
- Hitachi Inverter 101
- Hitachi IES Co., Ltd 103
- MICRO-EH 104
- Hollysys Corporation 108
- HuaDA HD-JZ06 110
- RS232 Port 112
- RS485 Port 112
- KDN Corporation 113
- Kinco Corporation 115
- Kinco ED Series 117
- Keyence Corporation 119
- Koyo Corporation 122
- PLC software setting 123
- KTC Srdlink 125
- RS232 communication 130
- RS485 communication 130
- XG5000 software setting 133
- LUST BUS Inverter 138
- Memory map 144
- Note: 1. Don’t live plug! 146
- 3Setting Your owner cable 147
- RS422 communication 148
- (support multi station) 151
- PLC Software Setting： 152
- RS485 communication 153
- modifiable 155
- Q00jCPU 159
- Q02CPU 160
- Mks controller 162
- Omron Corporation 169
- OPTO 22 179
- Register Type 181
- PMAC Motion Controller 185
- Profibus Slave 188
- PLC setting 189
- RF-IC (Card Reader) 193
- Saia-Burgess 194
- Systems Configuration 195
- Schneider Electric, Ltd 198
- PLC Setting 201
- Unitel-way protocol setting: 203
- Modbus protocol setting:： 203
- RS485communication 204
- SHIMADEN FP23 207
- SIEMENS 210
- Serial System configuration 211
- B）MPI address must be 2 215
- TMCM_303 228
- RS232 Communication Cable 230
- Trio motion controller 232
- Controller internal setting: 234
- RS485-4 communication 234
- Vigor Corporation 236
- XiLin Inverter 238
- Yamatake Corporation 240
- Yaskawa UDP 246
- 2. how to set the IP 248
- 248
- RS232 communication cable 254
- RS422 communication cable 254
- AI-7048 257
Verwandte Produkte und Handbücher für Nein Siemens KDN Series
Nein Siemens REV23.03RF Bedienungsanleitung
(13 Seiten)
(13 Seiten)
Nein Siemens KF Series Bedienungsanleitung
(3 Seiten)
(3 Seiten)
Nein Siemens Life 300 BTE Bedienungsanleitung
(28 Seiten)
(28 Seiten)
Nein Siemens eCharger Bedienungsanleitung
(1 Seiten)
(1 Seiten)
Nein Siemens Simatic S7-300 Wartungshandbuch
(272 Seiten)
(272 Seiten)
Nein Siemens ARTIS 2 S Wartungshandbuch
(606 Seiten)
(606 Seiten)
Nein Siemens CIELO 2 P Bedienungsanleitung
(2 Seiten)
(2 Seiten)
(8 Seiten)
Nein Siemens CENTRA Bedienerhandbuch
(36 Seiten)
(36 Seiten)
Nein Siemens ePen Bedienungsanleitung
(16 Seiten)
(16 Seiten)
Nein Siemens 5TC1 series Bedienungsanleitung
(4 Seiten)
(4 Seiten)
Nein Siemens GC..M.. Bedienungsanleitung
(7 Seiten)
(7 Seiten)
Nein Siemens KI42F Bedienungsanleitung
(20 Seiten)
(20 Seiten)
(2 Seiten)
Nein Siemens GS..D.. Bedienungsanleitung
(23 Seiten)
(23 Seiten)
Nein Siemens Pure 500 Betriebsanweisung
(36 Seiten)
(36 Seiten)
Nein Siemens PURE Bedienungsanleitung
(2 Seiten)
(2 Seiten)
Nein Siemens LZ53650 Bedienungsanleitung
(2 Seiten)
(2 Seiten)
Nein Siemens Pure SE Bedienungsanleitung
(10 Seiten)
(10 Seiten)
Nein Siemens MC55 Bedienungsanleitung
(3 Seiten)
(3 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.193 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern