Siemens EK 726 Series Wartungshandbuch PDF herunterladen (Seite 84)

COMMUNICATIONS / INTERFACES

MICROMASTER

MICROMASTER Vector

MIDIMASTER Vector

SIEMENS DA 64 – 2001/2002

Version C4 4/8

4.7 CAN bus module CB16

The CAN bus module was developed for operation with

MICROMASTER Vector / MIDIMASTER Vector and

supports the CAN Open protocol. It fulfills the

requirements of the CAN specification DS402.

All of the drive inverter parameters are accessible via

the bus. There are no restrictions regarding the

parameters harmonized in the DS402 specification.

The drive inverter I/O signals can be controlled via this

gateway. The "Device profile" for the I/O modules

(DS401) has not been implemented.

Designation Order No.

CAN bus module

6SE3290-0XX87-8CB0

Table 9: CAN bus ordering data

4.8 AS-Interface module

Designation Order No.

AS-Interface module

On request

Table 10: AS-Interface ordering data

4.9 Software tools

DVA-S5 software package to integrate the drive inverter

into a SIMATIC S5 control system via USS protocol or

PROFIBUS DP

Designation Order No.

Software package DVA-S5 6DD1800-0SW0

Table 11: DVA-S5 ordering data

supplied as: 3.5" floppy disk (1 x)

DriveMonitor and DriveES

DriveMonitor is the freely-available commissioning

(start-up) tool for drives from the following drive families

· MICROMASTER Basic / Vector / ECO

· MIDIMASTER Vector / ECO

and is supplied on the documentation CD (this is

included in the scope of supply).

Contrary to the DriveES basic software, DriveMonitor

operates without a project structure and exclusively on

the file system. Communications is only possible via

USS, which is also contrary to Drive ES basic software.

The drive commissioning software DriveMonitor runs

· Under MS Windows NT/MS Windows 2000: PG /

PC with a Pentium processor as well as a minimum

of 32 MB RAM. We recommend 64 MB of RAM.

· DriveMonitor requires approx. 75 Mbytes.

Comment:

SIMOVIS has been replaced by

DRIVE-MONITOR. Both

can be installed together on a computer but cannot be

simultaneously used.

Drive ES

The Drive ES (option) philosophy is to use an operator

interface as basis which many of our customers already

know, use and has been well proven as it operates with

SIMATIC (this has a No. 1 position in PLC systems)

and the associated software (STEP7 manager). By

using our drives, it is not necessary to learn a new

software environment. Drive ES is supplied in German,

English, French, Italian and Spanish. Drive ES

comprises four components, Drive ES Basic, Drive ES

Graphic (

not for MM3 drive inverters) and Drive ES

SIMATIC and Drive ES PCS7 which are individually

available:

Drive ES Basic

Allows drives to be parameterized both online and

offline.

Designation Order No.

Drive ES Basic 6SW1700-5JA00-1AA0

Table 12: DriveES Basic ordering data

supplied as: CD-ROM (1 x)

Drive ES SIMATIC

This requires that STEP 7 V5 SP 2 has been installed.

It provides a SIMATIC block library. This means that

PROFIBUS DP communications can be simply and

reliably programmed between the SIMATIC-CPU and

the drives.

Designation Order No.

Drive ES SIMATIC 6SW1700-5JC00-1AA0

Table 13: DriveEs Simatic ordering data

supplied as: CD-ROM (1 x)

Drive ES PCS7 (option) means that a PCS7 must have

been installed. It includes a PCS7 block library. The

screen and control blocks for drives are available.

Designation Order No.

Drive ES PCS7 6SW1700-5JD00-1AA0

Table 14: DriveEs PCS7 ordering data

supplied as: CD-ROM (1 x)

1 2 ... 79 80 81 82 83 84 85 86 87 88 89 ... 119 120

Kommentare zu diesen Handbüchern

Keine Kommentare

Siemens EK 726 Series Wartungshandbuch Seite 84

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Kochfelder Siemens EK 726 Series