Siemens Sinumerik 810T Bedienungsanleitung PDF herunterladen (Seite 81)

EMCO WINNC SINUMERIK 810/820 T ALARMS / MESSAGES

H 5

3006 Nxxxx Wrong block structure

Cause: too much M/H/T/D/S/G commands in one

block, G commands of the same group

twice programmed in block, circle with more

than 2 axes or polar coordinate centre

point with more than 2 axes, scale factor

programmed twice in a block, change of

plane / zero offset / tool change / mirror

while contour draft, no valid contour draft

with the programmed addresses

Remedy: correct program

3008 Nxxxx Subroutine error

Cause: subroutine counter invalid

subroutine end with M30

nesting depth override

Remedy: correct subroutine counter

program M17, max. 4 subroutines nested

3011 Nxxxx To many axes/axis twice

Cause: the position (axis) was already program-

med, too much axes with block with thread/

mirror

Remedy: correct program

3012 Nxxxx Block not in memory

Cause: program end without M30, jump target not

found

Remedy: correct program

3021 Nxxxx CRC contour error

Cause: The tool radius is too large in relation to the

smallest contour element, contour violation

with full circle, programmed arc radius

smaller than the tool radius

Remedy: correct program

3042 Wrong picture

Remedy: switch off / on the PC, reprot to EMCO if

repeatable

3049 Wrong simulation area

Cause: With graphik simulation no or an invalid

simulation area was put in

Remedy: put in/correct simulation area

3081 Nxxxx CRC not selected for approaching

Cause: With soft approaching / leaving a contour

G41 or G42 must be active

Remedy: correct program

4100 Nxxxx No D-number active

Cause: cycle alarm: no tooloffset active

Remedy: activate tool correction (D)

4101 Nxxxx Cutter radius = 0

Remedy: enter cutter radius

4102 Nxxxx Cutter radius too large

Remedy: correct cutter radius

4103 Nxxxx Tool to wide

Remedy: L93: use other tool

4120 Nxxxx Spindle rotat. dir. n. progr.

Remedy: L94: program spindle direction

4121 Nxxxx Spindle not in tol. range

4122 Nxxxx Calculated feed too large

Remedy: L841: reduce feed

4140 Nxxxx Fin. part diam. too small

Remedy: alter program

4180 Nxxxx Option not available !

Remedy: order option (L841, L94)

4200 Nxxxx Check definition of R

Remedy: correct R32

6000 - 7999 Machine alarms

see "Machine Alarms"

8004 ORDxx Failure main-drive unit

8005 - 8009 ORDxx Internal error AC

Remedy: report to EMCO if repeatable

8010 ORDxx Syncr. error main drive

Cause: synchronisation mark missing for main drive

Remedy: report to service technician, if repeatable

8011 - 8013 ORDxx Internal error AC

Remedy: report to EMCO, if repeatable

8014 ORDxx Decel.-time of axis too high

Remedy: report to service technician, if repeatable

8018 ORDxx Internal error AC

Remedy: report to EMCO, if repeatable

8021 ORDxx Internal error AC

Remedy: report to EMCO, if repeatable

8022 ORDxx Internal error AC

Remedy: report to EMCO, if repeatable

8023 ORDxx Invalid Z value for helix

Cause: The Z value of the helix must be smaller

than the length of the arc to be traversed

Remedy: Program correction

8100 Fatal init error AC

Cause: Internal error

Remedy: Restart software or reinstall when neces-

sary, report to EMCO, if repeatable.

8101 Fatal init error AC

see 8101.

8102 Fatal init error AC

see 8101.

8103 Fatal init error AC

see 8101.

1 2 ... 76 77 78 79 80 81 82 83 84 85 86 ... 89 90

Kommentare zu diesen Handbüchern

Keine Kommentare

Siemens Sinumerik 810T Bedienungsanleitung Seite 81

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Vernetzung Siemens Sinumerik 810T