Siemens Sinumerik 810T Bedienungsanleitung Seite 87
- Seite / 90
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
EMCO WINNC SINUMERIK 810/820 T ALARMS / MESSAGES
H 11
6013: MAIN DRIVE NOT READY
Main drive power supply defective or main drive too
hot, fuse defective, over- or undervoltage from mains.
A running program will be stopped, the auxilliary
drives will be switched off.
Check fuses or contact EMCO Service.
6014: NO MAIN SPINDLE SPEED
This alarm will be released, when the spindle speed
is lower than 20 rpm because of overload.
Alter cutting data (feed, infeed, spindle speed).
The CNC program will be aborted, the auxiliary
drives will be switched off.
6024: MACHINE DOOR OPEN
The door was opened while a machine movement.
The program will be aborted.
6040: TOOL TURRET INDEX FAILURE
The tool turret is in no locked position, tool turret
sensor board defective, cabling defective, fuse
defective.
A running CNC program will be stopped.
Swivel the tool turret with the tool turret key, check
fuses or contact EMCO service.
6041: TOOL CHANGE TIMEOUT
Tool drum stucks (collision?), fuse defective,
hardware defective.
A running CNC program will be stopped.
Check for collisions, check fuses or contact EMCO
service.
6043: TOOL CHANGE TIMEOUT
Tool drum stucks (collision?), fuse defective,
hardware defective.
A running CNC program will be stopped.
Check for collisions, check fuses or contact EMCO
service.
6046: TOOL TURRET ENCODER FAULT
Fuse defective, hardware defective.
Check fuses or contact EMCO service.
6048: CHUCK NOT READY
Attempt to start the spindle with open chuck or
without clamped workpiece.
Chuck stucks mechanically, insufficient pressured
air supply, fuse defective, hardware defective.
Check fuses or contact EMCO service.
6049: COLLET NOT READY
see 6048
PC TURN 120/125/155
The following alarms are valid for the
PC TURN 120/125/155.
6000: EMERGENCY OFF
The EMERGENCY OFF key was pressed.
The reference position will be lost, the auxiliary
drives will be switched off.
Remove the endangering situation and restart
machine and software.
6001: PLC-CYCLE TIME EXCEEDING
The auxiliary drives will be switched off.
Contact EMCO Service.
6002: PLC - NO PROGRAM CHARGED
The auxiliary drives will be switched off.
Contact EMCO Service.
6003: PLC - NO DATA UNIT
The auxiliary drives will be switched off.
Contact EMCO Service.
6004: PLC - RAM MEMORY FAILURE
The auxiliary drives will be switched off.
Contact EMCO Service.
6008: MISSING CAN SUBSCRIBER
Check fuses or contact EMCO Service.
6009: SAFETY CIRCUIT FAULT
Defective step motor system.
A running CNC program will be interrupted, the
auxiliary drives will be stopped, the reference position
will be lost.
Contact EMCO Service.
6010: DRIVE X-AXIS NOT READY
The step motor board is defective or too hot, a fuse
is defective, over- or undervoltage from mains.
A running program will be stopped, the auxiliary
drives will be switched off, the reference position will
be lost.
Check fuses or contact EMCO service.
6011: DRIVE Y-AXIS NOT READY
see 6010.
6012: DRIVE Z-AXIS NOT READY
see 6010.
- Software Description 1
- Contents 3
- E: @-Codes 4
- G: Survey Pages 4
- H: Alarms and Messages 4
- Starting Information 4
- A: Key Description 5
- Key functions 6
- Address and Numeric Keyboard 6
- Machine Control Keys 8
- KEY DESCRIPTION 9
- PC Keyboard 10
- Screen with Softkeys 11
- INNC SINUMERIK 810/820 T 12
- EY DESCRIPTION 12
- B: Basics 13
- Zero Offset 14
- Coordinate System 14
- Input of the 15
- Tool Data Measuring 16
- Cutter position 17
- Input of the Tool Data 18
- Tool Data Measuring with the 20
- Optical Presetting Device 20
- C: Operating Sequences 21
- Approach the Reference Point 22
- Input of the Gear Position 22
- Setting of Language and 22
- Workpiece directory 22
- Input of Programs 23
- PERATING SEQUENCES 24
- Program Administration 25
- Data Input-Output 25
- Program Run 29
- Graphic simulation 31
- D: Programming 33
- Survey of G Commands 34
- Survey of M Commands 34
- Survey of Cycles 34
- Description of G Commands 35
- G01 Linear Interpolation 35
- G02 Circular Interpolation 36
- Clockwise 36
- G03 Circular Interpolation 36
- Counterclockwise 36
- G04 Dwell 37
- G09 Exact Stop 37
- G10 - G13 Polar Coordinate 37
- Interpolation 37
- G25/G26 Programmable working 38
- G33 Thread Cutting 39
- Cutter Radius Compensation 39
- ROGRAMMING 40
- G48 Leave as Approached 42
- G50 Cancel Scale Modification 42
- G51 Scale Modification 42
- G54 - G57 Zero Offset 1 - 4 43
- G58/G59 Programmable Zero 43
- G60 Exact Stop Mode 44
- G63 Thread tapping with 44
- G70 Measuring in Inches 45
- G71 Measuring in Millimetre 45
- G92 Spindle Speed Limit 46
- G90 Absolute Programming 46
- G91Incremental Programming 46
- G94 Feed per Minute 49
- G95 Feed per Revolution 49
- G96 Constant Cutting Speed 49
- G97 Constant Spindle Speed 49
- G131 Transmit 50
- Description of Cycles 55
- L93 Cut-in Cycle 55
- L94 Undercut Cycle 56
- L97 Thread Cutting Cycle 58
- L971 Longitudinal Thread 58
- L98 Deep Hole Drilling Cycle 59
- L99 Thread Draft 60
- Contour definition 61
- Subroutines 63
- R PARAMETER 71
- OFFSET" 73
- Softkey Menu Survey 74
- Survey Guiding 76
- Control Alarms 78
- Machine Alarms 85
Verwandte Produkte und Handbücher für Vernetzung Siemens Sinumerik 810T
Vernetzung Siemens 505-2571 Spezifikationen
(68 Seiten)
(68 Seiten)
Vernetzung Siemens DTU3005-B Betreibershandbuch
(141 Seiten)
(141 Seiten)
Vernetzung Siemens MC35 Spezifikationen
(42 Seiten)
(42 Seiten)
Vernetzung Siemens SIMATIC TIWAY 1 Spezifikationen
(207 Seiten)
(207 Seiten)
Vernetzung Siemens TC35 Terminal Spezifikationen
(204 Seiten)
(204 Seiten)
Vernetzung Siemens TC35 Terminal Spezifikationen
(278 Seiten)
(278 Seiten)
Vernetzung Siemens RS-485 Wartungshandbuch
(92 Seiten)
(92 Seiten)
Vernetzung Siemens gigaset SE551 Bedienungsanleitung
(183 Seiten)
(183 Seiten)
Vernetzung Siemens SE505 Spezifikationen
(135 Seiten)
(135 Seiten)
Vernetzung Siemens RS-485 Wartungshandbuch
(46 Seiten)
(46 Seiten)
Vernetzung Siemens S7-200PLC Bedienungsanleitung
(21 Seiten)
(21 Seiten)
Vernetzung Siemens DTU3005-B Betreibershandbuch
(120 Seiten)
(120 Seiten)
Vernetzung Siemens 505-2571 Bedienungsanleitung
(30 Seiten)
(30 Seiten)
Vernetzung Siemens E-110-I Bedienungsanleitung
(10 Seiten)
(10 Seiten)
Vernetzung Siemens SL2-141 Bedienungsanleitung
(20 Seiten)
(20 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.064 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern