Siemens Sinumerik 810T Bedienungsanleitung Seite 86
- Seite / 90
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
EMCO WINNC SINUMERIK 810/820 T ALARMS / MESSAGES
H 10
6019: VICE TIMEOUT
24 V fuse defective, hardware defective.
Contact EMCO service.
6020: VICE FAILURE
24 V fuse defective, hardware defective.
Contact EMCO service.
6024: DOOR NOT CLOSED
The door was opened while a machine movement.
The program will be aborted.
6025: GEARBOX COVER NOT CLOSED
The gearbox cover was opened while a machine
movement. A running CNC program will be aborted.
Close the cover to continue.
6027: DOOR LIMIT SWITCH DEFECTIVE
The limit switch of the automatic door is displaced,
defective, wrong cabled.
Contact EMCO service.
6028: DOOR TIMEOUT
The automatic door stucks, the pressured air supply
is insufficient, the limit switch is displaced.
Check door, pressured air supply, limit switch or
contact EMCO service.
6030: NO PART CLAMPED
No workpiece inserted, vice cheek displaced, control
cam displaced, hardware defective.
Adjust or contact EMCO service.
6041: TOOL CHANGE TIMEOUT
Tool turret stucks (collision?), 24 V fuse defective,
hardware defective.
A running CNC program will be stopped.
Check for a collision or contact EMCO service.
6042: TOOL CHANGE TIMEOUT
see 6041.
6043: TOOL CHANGE TIMEOUT
see 6041.
6044: TOOL TURRET SYNC ERROR
Hardware defective.
Contact EMCO service.
6046: TOOL TURRET SYNC MISSING
Hardware defective.
Contact EMCO service.
6048: DIVIDING TIME EXCEEDED
Dividing head stucks, insufficient pressured air supply,
hardware defective.
Check for collision, check pressured air supply or
contact EMCO service.
6049: INTERLOCKING TIME EXCEEDED
see 6048
6050: FAILURE DIVIDING DEVICE
Hardware defective.
Contact EMCO service.
7000: INVALID TOOL NUMBER
The CNC program will be stopped.
Interrupt program with RESET and correct the pro-
gram.
7007: FEED HOLD
In the robotic mode a HIGH signal is at input E3.7.
Feed Stop is active until a low signal is at E3.7.
7017: GO FOR REFERENCE POINT
Approach the reference point.
7040: DOOR OPEN
The main drive can not be switched on and NC-Start
can not be activated.
Some accessories can be operated only with open
machine door.
Close the machine to run a program.
7043: PIECE COUNT REACHED
A predetermined number of program runs was
reached. NC-Start is locked. Reset the counter to
continue.
7050: NO PART CLAMPED
After switching on or after an alarm the vice is neither
at the open position nor at the closed position.
NC-Start is locked.
Traverse the vice manually on a valid end position.
7051: DIVIDING DEVICE NOT INTERLOCKED
After switching on or after an alarm the dividing head
is not in a lock position. NC-Start is locked.
- Software Description 1
- Contents 3
- E: @-Codes 4
- G: Survey Pages 4
- H: Alarms and Messages 4
- Starting Information 4
- A: Key Description 5
- Key functions 6
- Address and Numeric Keyboard 6
- Machine Control Keys 8
- KEY DESCRIPTION 9
- PC Keyboard 10
- Screen with Softkeys 11
- INNC SINUMERIK 810/820 T 12
- EY DESCRIPTION 12
- B: Basics 13
- Zero Offset 14
- Coordinate System 14
- Input of the 15
- Tool Data Measuring 16
- Cutter position 17
- Input of the Tool Data 18
- Tool Data Measuring with the 20
- Optical Presetting Device 20
- C: Operating Sequences 21
- Approach the Reference Point 22
- Input of the Gear Position 22
- Setting of Language and 22
- Workpiece directory 22
- Input of Programs 23
- PERATING SEQUENCES 24
- Program Administration 25
- Data Input-Output 25
- Program Run 29
- Graphic simulation 31
- D: Programming 33
- Survey of G Commands 34
- Survey of M Commands 34
- Survey of Cycles 34
- Description of G Commands 35
- G01 Linear Interpolation 35
- G02 Circular Interpolation 36
- Clockwise 36
- G03 Circular Interpolation 36
- Counterclockwise 36
- G04 Dwell 37
- G09 Exact Stop 37
- G10 - G13 Polar Coordinate 37
- Interpolation 37
- G25/G26 Programmable working 38
- G33 Thread Cutting 39
- Cutter Radius Compensation 39
- ROGRAMMING 40
- G48 Leave as Approached 42
- G50 Cancel Scale Modification 42
- G51 Scale Modification 42
- G54 - G57 Zero Offset 1 - 4 43
- G58/G59 Programmable Zero 43
- G60 Exact Stop Mode 44
- G63 Thread tapping with 44
- G70 Measuring in Inches 45
- G71 Measuring in Millimetre 45
- G92 Spindle Speed Limit 46
- G90 Absolute Programming 46
- G91Incremental Programming 46
- G94 Feed per Minute 49
- G95 Feed per Revolution 49
- G96 Constant Cutting Speed 49
- G97 Constant Spindle Speed 49
- G131 Transmit 50
- Description of Cycles 55
- L93 Cut-in Cycle 55
- L94 Undercut Cycle 56
- L97 Thread Cutting Cycle 58
- L971 Longitudinal Thread 58
- L98 Deep Hole Drilling Cycle 59
- L99 Thread Draft 60
- Contour definition 61
- Subroutines 63
- R PARAMETER 71
- OFFSET" 73
- Softkey Menu Survey 74
- Survey Guiding 76
- Control Alarms 78
- Machine Alarms 85
Verwandte Produkte und Handbücher für Vernetzung Siemens Sinumerik 810T
Vernetzung Siemens 505-2571 Spezifikationen
(68 Seiten)
(68 Seiten)
Vernetzung Siemens DTU3005-B Betreibershandbuch
(141 Seiten)
(141 Seiten)
Vernetzung Siemens MC35 Spezifikationen
(42 Seiten)
(42 Seiten)
Vernetzung Siemens SIMATIC TIWAY 1 Spezifikationen
(207 Seiten)
(207 Seiten)
Vernetzung Siemens TC35 Terminal Spezifikationen
(204 Seiten)
(204 Seiten)
Vernetzung Siemens TC35 Terminal Spezifikationen
(278 Seiten)
(278 Seiten)
Vernetzung Siemens RS-485 Wartungshandbuch
(92 Seiten)
(92 Seiten)
Vernetzung Siemens gigaset SE551 Bedienungsanleitung
(183 Seiten)
(183 Seiten)
Vernetzung Siemens SE505 Spezifikationen
(135 Seiten)
(135 Seiten)
Vernetzung Siemens RS-485 Wartungshandbuch
(46 Seiten)
(46 Seiten)
Vernetzung Siemens S7-200PLC Bedienungsanleitung
(21 Seiten)
(21 Seiten)
Vernetzung Siemens DTU3005-B Betreibershandbuch
(120 Seiten)
(120 Seiten)
Vernetzung Siemens 505-2571 Bedienungsanleitung
(30 Seiten)
(30 Seiten)
Vernetzung Siemens E-110-I Bedienungsanleitung
(10 Seiten)
(10 Seiten)
Vernetzung Siemens SL2-141 Bedienungsanleitung
(20 Seiten)
(20 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.084 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern