Siemens Sinumerik 810T Bedienungsanleitung Seite 85
- Seite / 90
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
EMCO WINNC SINUMERIK 810/820 T ALARMS / MESSAGES
H 9
9023 Control keyboard not connected
Remedy: Connect control keyboard, switch on ...
9024 General RS232 communication error
Remedy: Correct settings of the serial interface.
9500 Invalid memory for program
Cause: the PC has not enough free RAM
Remedy: Close all other WINDOWS applications,
eventually remove resident programs from
RAM, restart PC
9501 Error while saving program
Cause: disk full?
9502 Too less memory (loading prog.)
see 9500
9508 Selected menu not found
Remedy: report to EMCO, if repeatable
9509 Too less memory for picture
Remedy: report to EMCO, if repeatable
9510 Mem.-fail. block-search buffer
Remedy: report to EMCO, if repeatable
9511 Projection error block search
Remedy: report to EMCO, if repeatable
9540 Error in BFM / BFM not foand
Remedy: report to EMCO, if repeatable
Machine Alarms
These alarms are released by the machine.
The alarms are different for the PC TURN 50/55 and
the PC TURN 120/125/155.
The alarms 6000 - 6999 normally must be
acknowledged with RESET. The alarms 7000 - 7999
are messages which will disappear usually when the
alarm releasing situation is eliminated.
PC TURN 50/55
The following alarms are valid for the
PC TURN 50/55.
6000: EMERGENCY OFF
The EMERGENCY OFF key was pressed. Remove
the endangering situation and restart machine and
software.
6001: CYCLE TIME EXCEEDS LIMIT
Contact EMCO Service.
6002: NO PLC PROGRAM LOADED
Contact EMCO Service.
6003: DB NOT EXISTENT
Contact EMCO Service.
6004: RAM ERROR ON PLC BOARD
Contact EMCO Service.
6009: FAILURE SAFETY CIRCUIT
Defective door limit switch or main contactor. Opera-
ting the machine is not possible.
Contact EMCO Service.
6010: X-AXIS NOT READY
Step motor board defective or too hot, 24 V fuse
defective. Check fuses and switch box fan filter.
Contact EMCO Service.
6011: Y-AXIS NOT READY
see 6010.
6012: Z-AXIS NOT READY
see 6010.
6013: MAIN DRIVE NOT READY
Main drive power supply defective, cable defective,
fuse defective.
Check fuse.
Contact EMCO service.
6014: NO SPEED FOR MAIN SPINDLE
This alarm will be released, when the spindle speed
is lower than 20 rpm because of overload.
Alter cutting data (feed, infeed, spindle speed).
- Software Description 1
- Contents 3
- E: @-Codes 4
- G: Survey Pages 4
- H: Alarms and Messages 4
- Starting Information 4
- A: Key Description 5
- Key functions 6
- Address and Numeric Keyboard 6
- Machine Control Keys 8
- KEY DESCRIPTION 9
- PC Keyboard 10
- Screen with Softkeys 11
- INNC SINUMERIK 810/820 T 12
- EY DESCRIPTION 12
- B: Basics 13
- Zero Offset 14
- Coordinate System 14
- Input of the 15
- Tool Data Measuring 16
- Cutter position 17
- Input of the Tool Data 18
- Tool Data Measuring with the 20
- Optical Presetting Device 20
- C: Operating Sequences 21
- Approach the Reference Point 22
- Input of the Gear Position 22
- Setting of Language and 22
- Workpiece directory 22
- Input of Programs 23
- PERATING SEQUENCES 24
- Program Administration 25
- Data Input-Output 25
- Program Run 29
- Graphic simulation 31
- D: Programming 33
- Survey of G Commands 34
- Survey of M Commands 34
- Survey of Cycles 34
- Description of G Commands 35
- G01 Linear Interpolation 35
- G02 Circular Interpolation 36
- Clockwise 36
- G03 Circular Interpolation 36
- Counterclockwise 36
- G04 Dwell 37
- G09 Exact Stop 37
- G10 - G13 Polar Coordinate 37
- Interpolation 37
- G25/G26 Programmable working 38
- G33 Thread Cutting 39
- Cutter Radius Compensation 39
- ROGRAMMING 40
- G48 Leave as Approached 42
- G50 Cancel Scale Modification 42
- G51 Scale Modification 42
- G54 - G57 Zero Offset 1 - 4 43
- G58/G59 Programmable Zero 43
- G60 Exact Stop Mode 44
- G63 Thread tapping with 44
- G70 Measuring in Inches 45
- G71 Measuring in Millimetre 45
- G92 Spindle Speed Limit 46
- G90 Absolute Programming 46
- G91Incremental Programming 46
- G94 Feed per Minute 49
- G95 Feed per Revolution 49
- G96 Constant Cutting Speed 49
- G97 Constant Spindle Speed 49
- G131 Transmit 50
- Description of Cycles 55
- L93 Cut-in Cycle 55
- L94 Undercut Cycle 56
- L97 Thread Cutting Cycle 58
- L971 Longitudinal Thread 58
- L98 Deep Hole Drilling Cycle 59
- L99 Thread Draft 60
- Contour definition 61
- Subroutines 63
- R PARAMETER 71
- OFFSET" 73
- Softkey Menu Survey 74
- Survey Guiding 76
- Control Alarms 78
- Machine Alarms 85
Verwandte Produkte und Handbücher für Vernetzung Siemens Sinumerik 810T
Vernetzung Siemens 505-2571 Spezifikationen
(68 Seiten)
(68 Seiten)
Vernetzung Siemens DTU3005-B Betreibershandbuch
(141 Seiten)
(141 Seiten)
Vernetzung Siemens MC35 Spezifikationen
(42 Seiten)
(42 Seiten)
Vernetzung Siemens SIMATIC TIWAY 1 Spezifikationen
(207 Seiten)
(207 Seiten)
Vernetzung Siemens TC35 Terminal Spezifikationen
(204 Seiten)
(204 Seiten)
Vernetzung Siemens TC35 Terminal Spezifikationen
(278 Seiten)
(278 Seiten)
Vernetzung Siemens RS-485 Wartungshandbuch
(92 Seiten)
(92 Seiten)
Vernetzung Siemens gigaset SE551 Bedienungsanleitung
(183 Seiten)
(183 Seiten)
Vernetzung Siemens SE505 Spezifikationen
(135 Seiten)
(135 Seiten)
Vernetzung Siemens RS-485 Wartungshandbuch
(46 Seiten)
(46 Seiten)
Vernetzung Siemens S7-200PLC Bedienungsanleitung
(21 Seiten)
(21 Seiten)
Vernetzung Siemens DTU3005-B Betreibershandbuch
(120 Seiten)
(120 Seiten)
Vernetzung Siemens 505-2571 Bedienungsanleitung
(30 Seiten)
(30 Seiten)
Vernetzung Siemens E-110-I Bedienungsanleitung
(10 Seiten)
(10 Seiten)
Vernetzung Siemens SL2-141 Bedienungsanleitung
(20 Seiten)
(20 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.046 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern