Siemens Pacemaker UM344-2 Bedienungsanleitung Seite 28
- Seite / 183
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
UM344-2 INITIAL TRANSMITTER SET-UP
September 1995
3
-
5
The next screen to appear is used to save the
configuration to an archive. If the configuration is to
be edited, press YES (F4) to save the configuration
in case a mistake is made. The next screen will
prompt for an archive number (0-99). The archive
number chosen will be the location where the MXC
stores the transmitter's configuration data. Archiving
will be discussed in more detail in the Off-Line
portion of section 5.
The MXC can now be used to calibrate or configure the
transmitter, monitor loop parameters, or test loop
functionality. Section 5 of this Manual describes
configuring and monitoring of the transmitter, and
calibration is described in Section 6. The screen
selections to choose the options of configuration,
calibration, and loop checkout are found on the On-Line
menu screen.
3.3 TESTING THE
TRANSMITTER, MXC, AND THE
LOOP
The test routines available through the MXC are used to
verify that the Transmitter, the MXC, and the loop are all
working properly. Whenever a problem with any of the
instruments or the loop is suspected, test the equipment
to make sure there are no component failures. The test
functions can be accessed in two locations in the MXC,
and these are described below.
3.3.1 MXC Testing
PRESS ANY KEY TO
CONFIRM CONTACT
_ _ _ _ _ _ _ _ _ _ END
TEST
1. Press and momentarily hold the MXC's ON key.
The Main Menu will appear.
2. Press TEST MXC (F3) to display the MXC Self
Test screen.
3. Press one of the following keys.
TEST KEYS - Press to test MXC keys. At the next
screen, press any key on the keyboard and the
WOULD YOU LIKE TO
SAVE TRANSMITTER
DATA IN
ARCHIVES NO YES
Dev ID: 210300003C
Tag: TTC-101 ADD: 00
LOOP CAL/ CON -
END
OVRD
TEST FIG
ENTER ARCHIVE NUMBER
(0-99):
EN-
< > END TER
SELECT FUNCTION
FIND ARCH TEST
XMTR FUNC MXC END
MXC SELF TEST
TEST TEST
KEYS SCRN END
- USER’S MANUAL 1
- TABLE OF CONTENTS 2
- CONTENTS UM344-2 3
- September 1995 3
- UM344-2 CONTENTS 4
- September 1995 4
- SECTION AND TITLE PAGE 5
- LIST OF ILLUSTRATIONS 6
- LIST OF TABLES 7
- 1.0 INTRODUCTION 10
- FIGURE 1-1 Basic Model 344 11
- X02869S1 12
- 2.0 XTC COMMUNICATOR 14
- MOORE XTC COMMUNICATOR 15
- SELECT BLOCK TO EDIT 16
- - SENSOR INPUT 16
- PREV NEXT END ECT 16
- SELECT FUNCTION 18
- FIND ARCH TEST 18
- XMTR FUNC MXC END 18
- X02849S1 19
- LOOP OVERRIDE - CHOOSE 21
- CURRENT OUTPUT LEVEL 21
- 4 MA 20 MA OTHR END 21
- X02807S1 25
- SHORT OR LONG FORM 27
- ADDRESS? 27
- SHRT LONG 27
- ADDR ADDR POLL END 27
- MXC SELF TEST 28
- TEST TEST 28
- KEYS SCRN END 28
- WARNING! SELF TEST 30
- MAY BUMP TRANSMITTER 30
- OUTPUT A 30
- 4.0 INSTALLATION 35
- X02866S1 39
- X02867S1 40
- X02868S1 41
- X02817S1 42
- X02821S1 52
- Wall Mounting 53
- X02818S0 57
- FIGURE 4-8 Sensor Assembly 58
- X028AAS0 60
- X02870S1 61
- X02824S1 63
- TESTSIGNAL 66
- X02825S1 67
- MV LO : 0.0000 74
- ENTER MV LO: 74
- (F4) to change the setpoint 78
- DOWNLOADING 84
- CONFIGURATION 84
- - PLEASE WAIT 84
- DOWNLOAD 84
- COMPLETE 84
- MANUAL control mode to 92
- MANUAL control mode 92
- DG MR END CONT 96
- WARNING : ARCHIVE 97
- CONTAINS NO DATA 97
- A 97
- ERROR! ARCHIVE TYPE 98
- DOESN'T MATCH THE 98
- TRANSMITTER TYPE 98
- X02808S1 106
- X02827S1 1 of 2 111
- X02827S1 2 of 2 112
- APPLY 103.00 mV TO 115
- WITH COPPER WIRE 115
- CAL TEST END 118
- CALIBRATE / TEST 118
- TRANSMITTER PASSED 121
- TRANSMITTER SELFTEST 121
- 7.0 CIRCUIT DESCRIPTION 134
- Output Circuitry 135
- Input Circuitry 135
- X02815S0 142
- Z FS 146
- 9.0 GLOSSARY 154
- 4 - 20 mA 160
- Failsafe Level 160
- Absolute Alarm #1 161
- Absolute Alarm #2 161
- R = 162
- X02879S0 163
- Block Diagram, PD Controller 164
- Block Diagram, ID Controller 165
- X02881S1 168
- WARRANTY 177
- WARRANTY UM344-2 178
- W-2 October 1996 178
- PARTS LIST 179
- USER’S MANUAL ADDENDUM 181
- X03013S1 182
Verwandte Produkte und Handbücher für Messen, Testen & Steuern Siemens Pacemaker UM344-2
(22 Seiten)
(22 Seiten)
Messen, Testen & Steuern Siemens BTC-BR Handbuch
(264 Seiten)
(264 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.065 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern