Siemens IC60 Bedienungsanleitung Seite 29
- Seite / 172
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
System overview
29
Building Technologies
Fire Safety & Security Products
Outputs 1 & 2
Fully programmable, high current, open drain (high-going-low) type FET outputs
capable of switching up to 1 A @ 12 V DC. These 2 outputs are normally set as
switched outputs, providing power for 12 V sirens. If required, these outputs can be
programmed to be siren outputs designed to drive an 8 ohm 10 watt horn speaker
on each output (refer to chapter
16.1: Output options; Output D options, option 1;
P37E). Also if a horn speaker is connected to output #1 you may select (refer to
chapter
22.4: Listen dialing function through keypad and output; Output 1 Listen In;
P175E 7E) as the listen-dialing feature, to listen to the dialing sequence which than
could be heard at the speaker.
In IC60 compact unit the output 1 is assigned to operate the build in internal siren.
Output 3
This is a low current, open drain (high-going-low) type FET outputs capable of
switching up to 500 mA. Like outputs 1 & 2 it is fully programmable.
Connecting devices which draw current in excess of 500 mA to output 3/can
damage the output.
Output 4-Relay Out
Output 4 is a relay output with single pole changeover contacts. If required, the
Common (C) contact of the relay is connected by default to GND via JUMPER, the
jumper can be selected to 12 V or removed.
4.6 System Bus connection - keypad port
The terminals marked POS, NEG, CLOCK, & DATA make up the communications
port which the keypads and other intelligent bus devices use to communicate with
the Sintony 60. The terminals are connected to corresponding terminals on the
remote devices. The LIN terminal is only used by the keypads and utilizes a fifth
wire to provide a communicator listen-dialing facility (a dialing ton could be heard
through the buzzer). This feature is particularly useful when servicing monitoring
faults. The 12 V power supply (POS, NEG) of the bus is protected by a separate
thermal fuse.
4.7 Programming port
With the separate available programming cable IAQ6-1 and the programming
software Sylcom 60 IAS6-1 the Sintony 60 could be connected via this port directly
to a PC. All system parameters or settings could be easily changed with this
program. Furthermore this port could also be used to connect the memory stick
IMM6-10 to up or download the default setting of an alarm system. This speeds up
the process of programming, especially if similar settings have to be used with
different installations.
If the control panel is connected to the telephone line, the same software could be used to program/
monitor the control panel through the telephone line remotely, if the PC is equipped with a telephone
modem.
- Wireless and hardwired 1
- IC60 - Sintony 60 1
- Installer Manual 1
- Building Technologies 10
- 1 Terminology 12
- 2.1 New features 13
- 2.2 Changes 13
- 3 Programming to EN 50131 15
- 4 System overview 18
- 4.2 Sintony 60 compact 20
- Z1Z10V 0V12V 12VCCC 21
- CCZ5Z2 Z6Z3 Z7Z4 Z8 TAMP 21
- 4.3 Zone connections 25
- 4.3.2 Zone wiring examples 26
- PIR Internal Connections 27
- 4.4 Inputs hardwired 28
- 4.5 Outputs hardwired 28
- 4.7 Programming port 29
- 5.2 Panic functions 30
- 6 Voice board IAV6-90 33
- 6.2.1 Pre-configuration 34
- 6.2.2 Recording messages 36
- 6.2.3 Playing messages 36
- 6.2.4 Re-recording messages 36
- 6.3 Operating instructions 37
- 6.3.1.2 Auto answering 38
- 6.3.3.1 Output DTMF 39
- 6.3.2.2 Call-back 39
- 6.4 Mute siren 41
- 7.3 Radio receiver IRFW6 42
- 8 LCD keypad 43
- Sequence Action 47
- Language 48
- Keypad Number 1 49
- 8.6 Operating a LCD keypad 53
- 8.6.4 LCD quick view mode 54
- 8.6.7 Send manual test call 55
- Program ( 61
- ) Button 61
- 10 Default access codes 62
- 11 Programming users 63
- 11.2 User code type 64
- 11.3 User access options 65
- 11.4 User code privileges 66
- 11.5 Radio user type 67
- 11.6 Radio user privileges 67
- 11.10 User to output mask 70
- 13.1 Installer code 75
- 13.2 Duress digit 75
- 13.3 Dial report delay 75
- 13.5 Two trigger timer 76
- Miscellaneous Options 78
- P25E 10E1-8E 78
- Installer Options 79
- P25E 11E 1-8E 79
- Miscellaneous User Options 80
- P25E 13E 1-8E 80
- 15 Time and date setting 82
- 16 Outputs 84
- Outputs 85
- Output B Options 85
- P35E 1-8E 1-8E 85
- Output C Options 85
- P36E 1-8E 1-5E 85
- 16.4 Un-map an output 87
- 17 Areas 89
- Area B Options 90
- P46E 1-2E 1-8E 90
- (1 = Area A, 2 = Area B) 90
- 18 Keypads 97
- Keypad ARM Areas 99
- P74E 1-8E 1-2E 99
- Keypad ARM Access 99
- P75E 1-8E 1-8E 99
- Keypads 100
- Keypad STAY Areas 100
- P76E 1-8E 1-2E 100
- Keypad STAY Access 100
- P77E 1-8E 1-8E 100
- Keypad A Key Areas 101
- P78E 1-8E 1-2E 101
- Keypad A Key Options 101
- P79E 1-8E 1-8E 101
- Keypad B Key Areas 102
- P80E 1-8E 1-2E 102
- Keypad B Key Options 102
- P81E 1-8E 1-8E 102
- 18.8 Keypad to output mask 103
- 18.12 Keypad chime timer 105
- 19 Key-switches 107
- Key-switches 108
- Keyswitch Access 108
- P112E 1-2E 1-8E 108
- 20 Zones 109
- Zone B Options 111
- P123E 1-16E 1-8E 111
- Zone C Options 112
- P124E 1-16E 1-8E 112
- 20.9 Zone timing settings 118
- 20.9.2 Retrigger time 119
- 21 Time zones 121
- 22 Dialer 123
- Dialer B Option 124
- P175E 2E 1-8E 124
- 22.2 Auto answer ring count 125
- 22.3 Test call options 125
- 22.5 Dialing pre-fix numbers 127
- 23 Telephone numbers 129
- Telephone numbers 130
- Phone Options 131
- P183E 1-8E 1-8E 131
- 23.5 Dial progress options 132
- Phone B Reporting 133
- P187E 1-8E 1-8E 133
- Phone C Reporting 133
- P188E 1-8E 1-8E 133
- Phone D Reporting 134
- P189E 1-8E 1-8E 134
- Divert Options 136
- P193E 1-2E 1-8E 136
- 24 4 plus 2 program options 137
- 4 plus 2 program options 138
- 26 Contact ID code summary 141
- 27.5 Reset back to defaults 146
- 27.6 Start a call-back call 147
- 27.7 Installer code 147
- 28 User privileges chart 148
- User privileges chart 149
- 30.1 Installer menu 151
- 30.2 Installer: Users 152
- 30.3 Clock settings 153
- 30.4 Phone numbers 154
- 30.5 Dialer 155
- 30.6 Areas 156
- 30.7 Zones main 157
- 30.8 Zones outputs 158
- 30.9 Keypads 159
- 30.10 Outputs 160
- 30.11 Keyswitch 161
- 30.12 Miscellaneous 162
- 30.13 4+2 event codes 163
- 30.14 SIA event codes 164
- 30.15 Diagnostics 165
- 31 Support 166
- Support 171
- After a voice alarm ...: 171
Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme Siemens IC60
(50 Seiten)
(184 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.026 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern