Siemens Sinumerik 810T Bedienerhandbuch Seite 7
- Seite / 62
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
01.93 11 Alarms
11.6 Alarm list POWER ON
11.6 Alarm list POWER ON
Cause:
Scan:
Explanation:
Remedy:
Note:
1
Battery alarm - power supply
Voltage of back-up battery
• With POWER ON
• Cyclically
Replace battery (see Instruction Manual)
The battery voltage has dropped to such a level that buffering of the
user memories is only guaranteed for a short period.
Replace battery (see Instruction Manual).
Acknowledge alarm with
(from power supply unit version 6EV3055-0BC revision ”F”)
Do not switch control off, otherwise data may be lost !
Dispose of all batteries as special waste.
Cause:
Scan:
Effects:
Explanation:
Remedy:
3
PLC stop
PLC not ready
Cyclically
NC START disabled
• Setpoint 0 output
• NC Ready 2 (NCBB2) cancelled
• Servo enable cancelled after time in MD 156 has expired
• NC/PLC interface rendered inactive
• Resetting of all PLC outputs on I/O board
Cyclical and interrupt-driven operation of the PLC is interrupted.
Travel with the machine is not possible.
Using the PG (programmer) read out the cause of
interrupt (ISTACK). Evaluate PLC alarm on NC screen.
Scan:
Effect:
Explanation:
Remedy:
4
Incorrect unit system
• With POWER ON
• After modifying MD
• Conversion factor assumed to be 1
• An illegal combination has been selected (conversion factor greater
than ten) for the units of the measuring system (position control
resolution) and the unit of the input system.
• Position control resolution for rotary axis < 0.5 · 10
-3
degrees and
the ordering data option for this is missing.
Correct the MD bits then switch the control off and on or include the
ordering data option ”Position control resolution for rotary axis < 10
-3
degrees”
© Siemens AG 1990 All Rights Reserved 6ZB5 410-0DL02 11–7
SINUMERIK 810 GA3/820 GA3 (IA)
- 11 Alarms 1
- 11 Alarms 11.90 2
- 11.90 11 Alarms 3
- 11.4 Alarm display on screen 4
- 11.5 Display format 4
- 116* ORD12 Contour monitoring 5
- 11.5 Display format 6
- 11.6 Alarm list POWER ON 7
- Battery alarm - power supply 7
- PLC stop 7
- Incorrect unit system 7
- Too many inp. buffer param 8
- EPROM error 8
- Wrong axis/spindle assign 8
- Memory too small for UMS 9
- UMS error 9
- PP memory wrongly formatted 9
- Wrong UMS identifier 9
- RAM error on CPU 10
- RAM error on memory module 10
- 11.7 RS232C (V.24) Alarms 11
- Parity error RS232C (V.24) 11
- Overflow error RS232C (V.24) 11
- Frame error RS232C (V.24) 11
- PLC-alarm-mem. not formated 12
- Time monitoring RS232C (V.24) 12
- 09.91 11 Alarms 13
- 11.7 RS232C (V.24) Alarms 13
- Wrong data in MD 576* 17
- Error absolute submodule 17
- Illegal software limit switch 17
- DAC limit reached 18
- Clamping monitoring 19
- Contour monitoring 19
- Set speed too high 21
- Drift too high 21
- Servo enable trav. axis 21
- Stop behind reference point 22
- Axis in several channels 22
- + Working area limit 22
- - Working area limit 22
- Follow-up/park for axis 22
- 11.9 General RESET alarms 23
- Stop during threading 23
- Wrong path increment 23
- Emergency stop 23
- Speed reduction area 24
- Feed limitation 24
- G35 thread lead decr. error 24
- Prog. S value too high 25
- Path feed too great 25
- Reference point not reached 25
- Block not in memory 25
- Program not in memory 25
- Parity error in memory 26
- Progr. error on transform 26
- Block > 120 characters 26
- Option not available 26
- Circle end point error 27
- Travel thru transf. center 27
- 3D option not available 27
- G92 Program error 28
- TO, ZO Program error 28
- General program error 28
- Feed missing/not prog 28
- Thread lead too high 28
- Program error round axis 29
- Pos. behind SW overtravel 29
- Thread lead incr./decr 29
- Max. speed = 0 29
- CRC/TNRC not allowed 31
- CRC plane not determinable 31
- Coord. rotation n. allowed 32
- Battery alarm abs. submod. 1 32
- Battery alarm abs. submod. 2 32
- Spindle speed too high 32
- Control loop spindle - HW 33
- Spindle meas. system dirty 33
- Option M19 not available 33
- Scale factor not allowed 33
- Scale change not allowed 34
- Approach not possible 34
- Retract not possible 34
- Wrong appr./retract plane 34
- M function for C axis invalid 35
- Transformation undefined 35
- Transformation axes assigned 35
- Transformation in zero 35
- Axis doubling active 35
- No additional axes possible 36
- Option M 19 missing 37
- 11.11 Alarm list ACKNOWLEDGE 38
- Geometry parameters >5 38
- Polar/radius error 38
- Invalid address 38
- CL800 error 39
- Contour definition error 39
- Wrong block structure 39
- Wrong setting data program 40
- Subroutine error 40
- Program disabled 40
- Intersection error 40
- Simulation disabled 41
- External data input error 41
- Part program no. occurs twice 42
- Option RS 232 not available 42
- CRC/TNRC contour error 42
- Display description error 43
- Graphics / text too volum 43
- Graphics command too volum 43
- Cursor memory not available 44
- Display text not available 44
- Too many fields / variables 44
- Graphics option not available 44
- Text not available 45
- Fields / var. not displayable 45
- Variable error 46
- Wrong workpiece definition 46
- Wrong simulation area 46
- Incorrect input 46
- Data block not available 46
- CRC not selected on approach 47
- Feed limit fictitious axis 47
- Wrong data in DB 39 47
- Transformationsdaten-Fehler 47
- Spindle not synchronized 48
- M19 still active 48
- PLC user alarm 49
- Signal converter missing 49
- Illegal MC 5 code 49
- Illegal MC 5 parameter 49
- Transfer to missing DB 50
- Substitution error 50
- Missing MC 5 block 50
- DB missing 50
- Illegal segment LIR / TIR 50
- Overflow - BSTACK 51
- Overflow - ISTACK 51
- MC 5 instruction STS 51
- MC 5 - command STP 52
- Illegal MC 5 timer / counter 52
- Function macro 52
- System commands disabled 52
- MD 0000: Alarm byte No 52
- MD 0001: CPU load 53
- MD 0003: Alarm runtime 53
- MD 0005: Cycle time 53
- MD 0006: Last MC 5 time 53
- This arrangement n. permitted 53
- Illegal servo sampling time 54
- Gap in MC 5 memory 54
- Inputs assigned twice 54
- Outputs assigned twice 54
- Alarm byte missing 54
- Wrong I/O jumpering 55
- Synch. error basic program 55
- Synch. error MC 5 program 55
- Synch. error MC 5 data 55
- Illegal block basic program 55
- Illegal block MC 5 program 56
- Illegal block MC 5 data 56
- Sumcheck error MC 5 block 56
- Sumcheck error basic program 56
- No response from EU 56
- EU transmission error 57
- Impermissible warm restart 57
- Decoding DB not available 57
- Decoding DB not modulo 6 57
- Decoding DB too short 58
- Distributed I/Os changed 58
- Overtemperature in EU 58
- Stop via softkey PG 58
- Timeout: MC5 user 59
- Timeout: Link memory 59
- Timeout: LIR / TIR 59
- Timeout: TNB / TNW 59
- Timeout with I / O transfer 61
- Time exceeded STEP 5 61
- Runtime exceeded OB2 61
- Cycle time exceeded 61
- Processing time delay OB2 62
- Host PLC failure 62
- PLC user messages 62
Verwandte Produkte und Handbücher für Vernetzung Siemens Sinumerik 810T
Vernetzung Siemens 5890 Betriebsanweisung
(129 Seiten)
(129 Seiten)
Vernetzung Siemens AFI5100 Installationshandbuch
(12 Seiten)
(12 Seiten)
Vernetzung Siemens SE105 Installationsanleitung
(117 Seiten)
(117 Seiten)
Vernetzung Siemens IEEE802.11 Spezifikationen
(184 Seiten)
(184 Seiten)
Vernetzung Siemens IEEE802.11 Betriebsanleitung
(292 Seiten)
(292 Seiten)
Vernetzung Siemens CP 1515 Betriebsanleitung
(274 Seiten)
(274 Seiten)
Vernetzung Siemens E-110-I Bedienungsanleitung
(24 Seiten)
(24 Seiten)
Vernetzung Siemens CP 243-2 Betriebsanleitung
(48 Seiten)
(48 Seiten)
Vernetzung Siemens gigaset SE551 Spezifikationen
(148 Seiten)
(148 Seiten)
Vernetzung Siemens 505-2571 Bedienungsanleitung
(16 Seiten)
(16 Seiten)
Vernetzung Siemens KDN Series Spezifikationen
(382 Seiten)
(382 Seiten)
Vernetzung Siemens S7-200PLC Spezifikationen
(504 Seiten)
(504 Seiten)
Vernetzung Siemens CL-010 Bedienungsanleitung
(57 Seiten)
(57 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.049 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern