Siemens SINUMERIK 802D sl Spezifikationen Seite 301
- Seite / 392
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Cycle alarms
06/2007 Overview of alarms
2-301
" Siemens AG 2007 All Rights Reserved
SINUMERIK 802D sl, Diagnostics Manual, 06/2007 Edition
61269 Channel %1 block %2: External tool diameter too small
Parameters: %1 = Channel number
%2 = Block number, label
Definitions: Incorrect tool definition.
Alarm triggered by following cycle: CYCLE61.
Reaction: Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy: Check angle and diameter of the tool used.
Program Con-
tinuation:
Clear alarm with the RESET key. Restart part program
61270 Channel %1 block %2: Chamfer width too small
Parameters: %1 = Channel number
%2 = Block number, label
Definitions: Chamfer width selected too small.
Alarm triggered by the following cycles: E_SP_CHA, F_SP_CHA.
Reaction: Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy: Increase the chamfer width.
Program Con-
tinuation:
Clear alarm with the RESET key. Restart part program
61271 Channel %1 block %2: Chamfer width > tool radius
Parameters: %1 = Channel number
%2 = Block number, label
Definitions: Chamfer width larger than tool radius.
Alarm triggered by following cycles: E_SP_CHA, F_SP_CHA.
Reaction: Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy: Use a larger tool.
Program Con-
tinuation:
Clear alarm with the RESET key. Restart part program
61272 Channel %1 block %2: Insertion depth too small
Parameters: %1 = Channel number
%2 = Block number, label
Definitions: Insertion depth on chamfering too small.
Alarm triggered by following cycles: E_SP_CHA, F_SP_CHA.
Reaction: Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy: Increase the insertion depth.
Program Con-
tinuation:
Clear alarm with the RESET key. Restart part program
- SINUMERIK 802D sl 1
- SINUMERIK® Documentation 2
- General alarms 7
- Table of Contents 1 9
- Overview of alarms 2 13
- Overview of alarms 06/2007 40
- NCK alarms/ISO alarms 40
- Example: 102
- 2: Base frame 189
- Reaction: Alarm display 189
- - Axis replacement 192
- Reaction: Interpreter stop 197
- tool was selected before 202
- Program Con 203
- %3 = T number of first tool 203
- ($AA_TOFF) is cleared 238
- 2.2 Cycle alarms 269
- > "Spindles" 298
- Cycle alarms 331
- 06/2007 Overview of alarms 331
- 2.3 Profibus alarms 332
- Profibus alarms 337
- 2.4 PLC alarms 338
- 2.5 SINAMICS-Parameters 340
- List of action numbers 3 341
- Remedy 365
- System reactions on alarms 4 367
- Cancel criteria for alarms 370
- Appendix A 373
- Appendix 06/2007 374
- Abbreviations 374
- 06/2007 Appendix 375
- 06/2007 Index 389
- (OHFWURQLFGRFXPHQWDWLRQ 392
- 8VHUGRFXPHQWDWLRQ 392
Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme Siemens SINUMERIK 802D sl
(150 Seiten)
(184 Seiten)Whirlpool Raffreddamento per bevande manuali utente
Partendo da I
Kommentare zu diesen Handbüchern