Siemens SINUMERIK 802D sl Betreibershandbuch PDF herunterladen (Seite 242)

Overview of alarms 06/2009

Cycle alarms

2-242

SINUMERIK 802D sl, Diagnostics Manual, 06/2009

Definitions: The alarm is triggerd by the following cycles: CYCLE997, CYCLE119

Remedy: Set MD 28081>0, $P_CHBFRMASK>0

61413 [Channel %1: ] Block %2: check setpoint of ball diameter, _SETVAL<=0

Parameters: %1 = Channel number

%2 = Block number, label channel number

Definitions: The alarm is triggerd by the following cycles: CYCLE997

Remedy: Check setpoint value of spherical diameter.

61414 [Channel %1: ] Block %2 : distortion of triangle over limit

Parameters: %1 = Channel number

%2 = Block number, label channel number

Definitions: The alarm is triggerd by the following cycles: CYCLE997, CYCLE119

Remedy: Check the setpoint and actual values

61415 [Channel %1: ] Block %2: check probe / machining plane

Parameters: %1 = Channel number

%2 = Block number, label channel number

Definitions: The alarm is triggerd by the following cycles: CYCLE971

Remedy: Enter permissible probe (_TP[x,8], _TPW[x,8]) for machining plane or change machining plane.

61416 [Channel %1: ] Block %2: adapt array size %4!

Parameters: %1 = Channel number

%2 = Block number, label channel number

Definitions: "Adjust field size _TP[ ]/_CVAL[0]!" or "Adjust field size _WP[ ]/_CVAL[1]!" or "Adjust field size _KP[

]/_CVAL[2]!" or "Adjust field size _TWP[ ]/_CVAL[3]!". Check probe/machining plane.

Alarm triggered by following measuring cycles: all measuring cycles.

Remedy: Adjust _CVAL entry with the number of available probe or calibration block data fields.

61417 [Channel %1: ] Block %2: Probe will collide with the carrier of the

reference groove.

Parameters: %1 = Channel number

%2 = Block number, label channel number

Definitions: The alarm can be triggered by the following measuring cycles: CYCLE973

Remedy: Take up collision-free initial position of the axes involved in the measuring process.

61418 [Channel %1: ] Block %2: Protocol file too small, check MD11420:

LEN_PROTOCOL_FILE.

Parameters: %1 = Channel number

%2 = Block number, label channel number

Definitions: Alarm can be triggered by following measuring cycle: CYCLE106

Remedy: Check MD11420: LEN_PROTOCOL_FILE.

61419 [Channel %1: ] Block %2: Check probe calibration with reference to

center of ball/circumference of ball.

Parameters: %1 = Channel number

%2 = Block number, label channel number

Definitions: The alarm can be triggered by the following measuring cycles: CYCLE974, CYCLE994, CYCLE977,

CYCLE978, CYCLE979, CYCLE997, CYCLE998

Remedy: The workpiece probe must be calibrated according to its use in the measuring cycles.

61420 [Channel %1: ] Block %2: Check calibration of multi/mono probes.

Parameters: %1 = Channel number

%2 = Block number, label channel number

Definitions: The alarm can be triggered by the following measuring cycles: CYCLE974, CYCLE994, CYCLE977,

CYCLE978, CYCLE979, CYCLE997, CYCLE998

Remedy: The workpiece probe must be calibrated according to its type and use.

1 2 ... 237 238 239 240 241 242 243 244 245 246 247 ... 339 340

Kommentare zu diesen Handbüchern

Keine Kommentare

Siemens SINUMERIK 802D sl Betreibershandbuch Seite 242

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme Siemens SINUMERIK 802D sl