Siemens SINUMERIK 802D sl Betreibershandbuch PDF herunterladen (Seite 84)

Overview of alarms 06/2009

NCK alarms

2-84

SINUMERIK 802D sl, Diagnostics Manual, 06/2009

12540 [Channel %1: ] Block %2 Block is too long or too complex

Parameters: %1 = Channel number

%2 = Block number, label

Definitions: The maximum internal block length after translator processing must not exceed 256 characters. After

editing, for example, several macros in the block or a multiple nesting, this limit can be exceeded.

Reaction: Correction block is reorganized.

Interface signals are set.

Alarm display.

Remedy: Press the NC Stop key and select the function "Correction block" with the softkey PROGRAM COR-

RECT. The correction pointer positions on the incorrect block.

Divide up the program block into several subblocks.

Program Con-

tinuation:

Clear alarm with NC START or RESET key and continue the program.

12550 [Channel %1: ] Block %2 name %3 not defined or option/function not

activated

Parameters: %1 = Channel number

%2 = Block number, label

%3 = Source symbol

Definitions: The identifier displayed has not been defined before being used.

_N_SMAC_DEF

_N_MMAC_DEF

_N_UMAC_DEF

_N_SGUD_DEF

_N_MGUD_DEF

_N_UGUD_DEF

Variable: DEF statement is missing

Program: PROC declaration is missing

Reaction: Correction block is reorganized.

Interface signals are set.

Alarm display.

Remedy: Press the NC Stop key and select the function "Compensation block" with the softkey PROGRAM

CORRECT. The cursor positions itself on the incorrect block.

- Correct the name used (writing error)

- Check definitions of variables, subroutines and macros

- Declare subroutine with EXTERN, load subroutine to SPF-Dir

- Check interface definition of subroutine

- Check options. See also MD10711 $MN_NC_LANGUAGE_CONFIGURATION.

Program Con-

tinuation:

Clear alarm with NC START or RESET key and continue the program.

12552 [Channel %1: ] Block %2 tool/magazine OEM parameter not defined.

Option not set. Option not set.

Parameters: %1 = Channel number

%2 = Block number, label

Definitions: The programmed $TC_... Cx system variable is not known in the control.

Reaction: Correction block is reorganized.

Interface signals are set.

Alarm display.

Remedy: - Correct the name used (writing error)

- $TC_DPCx, $TC_TPCx, $TC_MOPCx, $TC_MAPCx, $TC_MPPCx, $TC_DPCSx, $TC_TPCSx,

$TC_MOPCSx, $TC_MAPCSx, $TC_MPPCSx; with x=1,...10

- These are the OEM parameters of the tools magazines, The corresponding machine data value is

set to < 10, or the option 'TM OEM parameters' has not been set.

- Use correct parameter number, or - if the name cannot be changed - set machine data correction

(see MD18096 $MN_MM_NUM_CC_TOA_PARAM, ... MD18206

$MN_MM_NUM_CCS_TOA_PARAM, ...). )

- Check the option (machine data are only effective when the option is enabled).

1 2 ... 79 80 81 82 83 84 85 86 87 88 89 ... 339 340

Kommentare zu diesen Handbüchern

Keine Kommentare

Siemens SINUMERIK 802D sl Betreibershandbuch Seite 84

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme Siemens SINUMERIK 802D sl